Online rumours about Chinese e-waste imports dismissed as “fake news” – Thai PBS World

Thai Public Broadcasting Service
145 Viphavadi Rangsit Rd.,
Talat BangKhen, Laksi,
Bangkok 10210, Thailand
145 Vibhavadi Rangsit Rd, Bangkok 10900
© 2026 Thai PBS World. All rights reserved.
Share
The government today rejected online rumours claiming that Thailand has agreed to import electronic waste from China, explaining that a recently approved bilateral project is strictly an 18-month knowledge-transfer programme on recycling electric vehicle (EV) batteries and solar panels.
Speaking at Government House at 9.15am today, Deputy Government Spokeswoman Lalida Persvivatana claimed that social media reports alleging that the Cabinet had approved the dumping of Chinese e-waste in Thailand are completely false.
She explained that, on October 27, the Cabinet endorsed a draft agreement under the Lancang-Mekong Cooperation Special Fund. One of the initiatives aims to build capacity in Thailand’s recycling industry, to support the circular economy and green industries, specifically targeting the future management of spent EV batteries, solar panels and domestic e-waste.
“With EV adoption rising rapidly in Thailand, the country will inevitably face long-term challenges in recycling batteries and solar panels,” Lalida said, adding that “This 18-month project is solely for training and knowledge development, not importing foreign waste.”
She stressed that Thai law strictly prohibits both any importation of electronic waste, insisting that Prime Minister Anutin Charnvirakul’s administration is taking uncompromising action against illegal waste dumping.
Under Anutin’s directive, a dedicated committee, chaired by Commerce Minister Suphajee Suthumpun, has been leading ongoing crackdowns, including tighter import-export inspections, factory audits and legal reforms to impose stiffer civil and criminal penalties on polluters, including deportation for foreign offenders.
While welcoming public scrutiny, Lalida urged media outlets and social media users to verify facts, rather than distorting partial information for views and likes, adding that the government has no intention of turning Thailand into “the world’s dumping ground.”
She also reiterated the administration’s commitment to environmental and public health protection, noting that Foreign Affairs Minister Sihasak Phuangketkeow will lead international talks later this month to address heavy metal contamination, including elevated arsenic and mercury levels in the Kok and Sai rivers.
Senate election fraud allegation comes closer to Anutin
Tuk-tuks might no longer operate in inner Bangkok
What are effective strategies to fact check information online?
Thai PM’s first official visit to Indonesia in 15 years
Thailand’s Phra Mahathat Temple eyes UNESCO World Heritage status

source

Posted in Renewables | Leave a comment

Heir says solar panel company is withholding money owed unless they sign a 13-year deal and waive claims – Yahoo Finance

Heir says solar panel company is withholding money owed unless they sign a 13-year deal and waive claims  Yahoo Finance
source

Posted in Renewables | Leave a comment

PLI scheme adds 24 GW to India’s solar module manufacturing capacity: NITI Aayog – BioEnergy Times

PLI scheme adds 24 GW to India’s solar module manufacturing capacity: NITI Aayog
EV adoption unlikely to slow India’s road-fuel demand growth before 2034: BNEF
Meta signs multi-year green steel certificates deal with Stegra
‘High SAF costs and limited supply remain major hurdles to aviation decarbonisation’: Asia Pacific Airlines chief
US fuel ethanol inventories decline slightly to 24.3 million barrels
Prahlad Joshi offers joint fuel testing amid Karnataka ethanol blending dispute
Ethanol blending controversy: Joshi cites OMC tests to counter Karnataka findings
Keralam inspects petrol pumps, sends E20 samples for laboratory testing
Oil companies reject Karnataka’s claim of 26–31% ethanol in petrol, question testing procedure
Declaration puts biogas and biomethane on global climate agenda at COP31
Telangana: Malkajgiri converts hotel food waste into cooking gas for Indiramma canteen
GAIL proposes Rs 123-crore municipal waste-based CBG plant in Bengaluru
Uttar Pradesh turns crop residue into economic opportunity through CBG production
Proposed CBG plant at Sainik School Kazhakootam faces opposition from parents, alumni
Chevron to restart Iowa biodiesel plant after two-year shutdown
Chevron decision to restart Iowa biodiesel facility displays power of robust renewable fuel standard blending levels
Marine biodiesel demand could exceed 12 billion litres by 2031 under IMO net-zero framework: IEA
Thailand’s biodiesel production, consumption expected to rise 22% in 2026: USDA
Indonesia plans to restart 600,000-tonne biodiesel plant to support B50 programme
Germany restricts subsidies for electricity generated from industrial wood
Privilege Biksons Boilers secures 185 TPH boiler and 32 MW turnkey cogeneration EPC order from Shri Halasiddhanath Sugar Factory
Biomass burning, vehicles major contributors to Delhi’s worsening air pollution
Corncob and African birch wood blend offers potential for sustainable solid biofuel production
Andhra University study finds seasonal variations in plankton biomass along Visakhapatnam coast
Meta signs multi-year green steel certificates deal with Stegra
Mercedes-Benz, HyIron partner to scale up green hydrogen-based iron production
Uniper and VNG starts production of green hydrogen
UAE-based Sahamco unveils $25 billion green hydrogen and ammonia project in Morocco
India commissions 8,000 tonnes of annual green hydrogen capacity as mission gathers pace
‘High SAF costs and limited supply remain major hurdles to aviation decarbonisation’: Asia Pacific Airlines chief
Phillips 66, United Airlines deliver 11 million gallons of sustainable aviation fuel
TotalEnergies to supply sustainable aviation fuel to DHL Express at Paris-CDG
Tecnicas Reunidas secures FEED contract for 66,000-tonne e-SAF plant in Sweden
APSAC, ISCC join hands to promote SAF certification across Asia-Pacific
India’s solar module manufacturing capacity has increased nearly 15 times, from around 8 GW to nearly 116 GW, with projects supported by the Production Linked Incentive (PLI) scheme contributing about 24 GW, according to a NITI Aayog report, ANI reported.
The report said PLI-supported projects account for around 20.7% of the country’s total solar photovoltaic (PV) module manufacturing capacity, reflecting the scheme’s contribution to expanding domestic production.
The High Efficiency Solar PV Modules PLI scheme has an allocation of Rs 24,000 crore. It aims to increase domestic manufacturing, promote the use of advanced technology and reduce dependence on imported solar modules. Total investment under the scheme stood at Rs 64,873 crore by March 2026.
The increase in domestic manufacturing has been accompanied by a fall in imports and growth in exports. Imports of solar PV modules declined from around USD 4.35 billion in 2023-24 to USD 2.15 billion in 2024-25.
India’s solar module exports increased from USD 83 million in 2021-22 to USD 1.97 billion in 2023-24. They remained relatively strong at around USD 1.12 billion in 2024-25, the report said.
The scheme has also encouraged manufacturers to source more materials and components from within the country. Incentives are linked to the extent of domestic content used in production, with the aim of building a stronger and more connected solar manufacturing industry.
The report said the scheme had delivered encouraging initial results in attracting investment, increasing manufacturing capacity, reducing imports and expanding exports.
However, it noted that the impact on employment and production was still developing, as several manufacturing units were gradually increasing their output.
The assessment also highlighted challenges from falling global solar module prices, partly due to excess manufacturing capacity and aggressive pricing by Chinese manufacturers. Limited availability of some important materials and China’s continued dominance in the global solar supply chain were other concerns.
According to the report, the scheme’s long-term success will depend on manufacturers increasing the use of domestically sourced materials, keeping production costs competitive, expanding their capabilities across the solar manufacturing chain and maintaining export growth amid changing global market conditions, ANI stated.
JOIN OUR MAIL LIST

Please Select “I agree to get email updates” options.
Email field is required to subscribe.

You Have Successfully Subscribed to the Newsletter
JOIN OUR MAIL LIST

Please Select “I agree to get email updates” options.
Email field is required to subscribe.

You Have Successfully Subscribed to the Newsletter

BioEnergy Times brings the latest News & Information from India & around the world related to the BioFuels and BioEnergy.
Contact us: news@bioenergytimes.com

© Copyright 2026 BioEnergy Times

source

Posted in Renewables | Leave a comment

India’s Solar Module Capacity Surges 15-Fold To 116 GW On PLI Push – Sarkaritel.com

India’s solar photovoltaic module manufacturing capacity has increased nearly 15-fold, from around 8 GW to nearly 116 GW, with projects supported under the Production Linked Incentive (PLI) scheme contributing approximately 24 GW. A NITI Aayog report highlighted the scheme’s role in attracting investment, reducing imports and strengthening domestic solar manufacturing.
New Delhi, Nov 16: India’s solar photovoltaic (PV) module manufacturing capacity has surged nearly 15-fold to around 116 GW, from approximately 8 GW, with support from the Production Linked Incentive (PLI) scheme, according to a report by NITI Aayog.
Projects supported under the scheme have contributed around 24 GW of manufacturing capacity, accounting for approximately 20.7% of India’s current solar module manufacturing capacity.
The expansion reflects the growing role of domestic manufacturing incentives in strengthening India’s solar energy supply chain and reducing dependence on imported modules.
The High Efficiency Solar PV Modules PLI Scheme, with an approved outlay of ₹24,000 crore, aims to promote large-scale domestic manufacturing, encourage advanced technologies and reduce dependence on imports.
According to the NITI Aayog report, cumulative investment under the scheme reached ₹64,873 crore by March 2026.
The scheme also encourages manufacturers to increase domestic sourcing by linking incentives to local value addition. This approach is intended to develop a more integrated solar manufacturing ecosystem in India.
The expansion in domestic manufacturing capacity has coincided with a decline in solar PV module imports and an increase in exports, although export values moderated in 2024-25.
The decline in imports indicates a shift towards domestic sourcing, while the rise in exports reflects the growing international presence of India’s solar module manufacturers.
The NITI Aayog report said the scheme had delivered strong early outcomes in investment mobilisation, manufacturing capacity creation, import substitution and export expansion.
Despite the expansion in domestic manufacturing, the report flagged challenges arising from falling global solar module prices. These have been partly driven by excess manufacturing capacity and aggressive pricing by Chinese producers.
The long-term effectiveness of the scheme will depend on manufacturers achieving higher domestic value addition, maintaining global cost competitiveness and developing capabilities across the wider solar manufacturing value chain.
Sustaining export growth amid changing international market conditions will also remain important for the sector.
The government has described the broader PLI framework as one of India’s most significant industrial policy interventions.
As of June 30, approved applications under the scheme stood at 791 across 14 sectors. Cumulative investment exceeded ₹2.58 lakh crore, while cumulative production and sales crossed ₹23.79 lakh crore.
The solar PV manufacturing programme is part of this broader effort to strengthen domestic industrial capabilities, attract investment and improve India’s position in global manufacturing supply chains.
The expansion of India’s solar module manufacturing capacity to nearly 116 GW highlights the growing contribution of the PLI scheme to domestic production and investment. However, sustaining this momentum will require greater local value addition, competitive manufacturing costs, deeper supply-chain capabilities and stronger export performance.

source

Posted in Renewables | Leave a comment

Karnataka Explores 1,500 MW Floating Solar Potential – Construction World

The Karnataka Power Corporation (KPCL) has invited bids for feasibility studies, bathymetric surveys and the preparation of detailed project reports (DPRs) for the proposed floating solar photovoltaic projects. The studies are intended to identify locations that are technically viable and environmentally sustainable for future development.
Energy and Tourism Minister KJ George said the state was assessing the potential for floating solar projects across suitable reservoirs. He said the programme aimed to make productive use of reservoir surfaces while supporting the state’s broader renewable energy objectives.
Floating solar projects use photovoltaic panels installed on specially designed structures that are anchored in reservoirs or other suitable water bodies. The installations can generate renewable electricity while limiting the need for land acquisition, making them an option for areas where land-based solar development may face constraints.
The proposed assessments will examine reservoir characteristics, water depths and seasonal variations in water levels. They will also evaluate the technical and economic feasibility of the projects before decisions are taken on their future development. The findings from the surveys and reports are expected to provide the basis for identifying suitable sites and determining the scale of projects that can be installed at each location.
KPCL’s invitation for bids marks the preliminary stage of the initiative. The feasibility work will help establish whether the targeted reservoirs can support floating structures and associated power infrastructure while maintaining environmental and operational suitability. Karnataka is pursuing the assessment as part of its efforts to broaden its renewable energy portfolio and improve the productive use of existing water resources.
The Karnataka government is exploring the development of 1,500 MW of floating solar power projects across suitable reservoirs and other water bodies as part of efforts to expand renewable energy generation and strengthen long-term energy security. The initiative could allow the state to add solar capacity without requiring large tracts of land. The Karnataka Power Corporation (KPCL) has invited bids for feasibility studies, bathymetric surveys and the preparation of detailed project reports (DPRs) for the proposed floating solar photovoltaic projects. The studies are intended to identify locations that are technically viable and environmentally sustainable for future development. Energy and Tourism Minister KJ George said the state was assessing the potential for floating solar projects across suitable reservoirs. He said the programme aimed to make productive use of reservoir surfaces while supporting the state’s broader renewable energy objectives. Floating solar projects use photovoltaic panels installed on specially designed structures that are anchored in reservoirs or other suitable water bodies. The installations can generate renewable electricity while limiting the need for land acquisition, making them an option for areas where land-based solar development may face constraints. The proposed assessments will examine reservoir characteristics, water depths and seasonal variations in water levels. They will also evaluate the technical and economic feasibility of the projects before decisions are taken on their future development. The findings from the surveys and reports are expected to provide the basis for identifying suitable sites and determining the scale of projects that can be installed at each location. KPCL’s invitation for bids marks the preliminary stage of the initiative. The feasibility work will help establish whether the targeted reservoirs can support floating structures and associated power infrastructure while maintaining environmental and operational suitability. Karnataka is pursuing the assessment as part of its efforts to broaden its renewable energy portfolio and improve the productive use of existing water resources.
The Ministry of Heavy Industries (MHI) has received 22 bids for 10 GWh of advanced chemistry cell (ACC) manufacturing capacity under the Production Linked Incentive (PLI) scheme. The bidders include Reliance Industries, ACME Solar Holdings, Amara Raja Advanced Cell Technologies, Exide Energy Solutions, JSW Neo Energy and Vikram Solar. The capacity has been earmarked for Grid-Scale Stationary Storage (GSSS) applications. It forms part of the government’s broader target of establishing 50 GWh of ACC manufacturing capacity under the National Programme on Advanced Chemistry Cell Battery Storage…
Prime Minister Narendra Modi has cited the electrification of the Indian Railways as an example of accelerated execution under his administration. Addressing the media at a Diwali Milan programme at the Bharatiya Janata Party headquarters in New Delhi, he compared the pace of infrastructure development and welfare delivery over the past decade with earlier periods. Modi said railway electrification began in the 1930s but had reached only 30 per cent completion by 2014, after about 90 years of work. He said the project would have taken several more decades at the earlier pace, while claiming th..
Northern Railway’s Jammu Division has raised the speed limit on Railway Bridge No. 232 in the Kandrori-Pathankot Cantt Block Section from 30 kmph to 45 kmph after extensive restoration and rehabilitation work. The bridge is located in the Bhogpur Sirwal-Pathankot Cantt Section and carries both UP and DN lines. The bridge’s protection walls were damaged during severe floods in 2024, prompting the imposition of a 20 kmph speed restriction from August 1, 2024. During the 2025 floods, the restriction was tightened on safety grounds to Stop Dead and 10 kmph. It was later relaxed in stages to 20..
Get daily newsletters around different themes from Construction world.
Don’t miss out on valuable insights and opportunities
to connect with like minded professionals

A-303, Navbharat Estates, Zakaria Bunder Road, Sewri (West), Mumbai – 400 015, Maharashtra, India
By creating an account, you agree to our Terms and Conditions and have read and acknowledge the Privacy Policy

test
Don’t miss out on valuable insights and opportunities
to connect with like minded professionals

By creating an account, you agree to our
Terms and Conditions and have read and acknowledge the Privacy Policy

test

source

Posted in Renewables | Leave a comment

Alpex Solar H1 revenue falls 2.02%, Q2 profit drops 61.65% – Power Peak Digest


Alpex Solar Limited reported revenue of Rs 885.01 crore for the first half (H1) of financial year 2026-27 (FY27), down 2.02% year on year (YoY) from Rs 903.24 crore in the corresponding period of the previous fiscal. Profit for the half-year stood at Rs 60.06 crore, a decline of 36.74% from Rs 94.95 crore in H1 of FY26.
Quarterly results
For the second quarter (Q2) ended September 30, 2026, revenue from operations was Rs 381.59 crore, down 27.03% YoY from Rs 522.92 crore in Q2 of FY26. On a quarter-on-quarter (QoQ) basis, revenue fell 24.20% from Rs 503.42 crore in the first quarter (Q1) of FY27.
Profit for the quarter was Rs 20.20 crore, down 61.65% YoY from Rs 52.67 crore a year earlier. Compared with the preceding quarter, profit declined 49.34% from Rs 39.87 crore in Q1 FY27.
Segments
The company has disclosed five operating segments under the management approach: solar panels, solar pumps, engineering, procurement and construction (EPC), solar cells, and independent power producers (IPP). The revised segment reporting has been adopted from the current financial year and reflects how the chief operating decision maker (CODM), identified as the company’s chief executive officer (CEO), reviews and evaluates business performance.
Cell plant
In its financial results, Alpex Solar outlined its manufacturing expansion plans, including a 2.2 GW G12R third-generation tunnel oxide passivated contact (TOPCon) solar cell manufacturing facility. The company expects the facility to commence commercial production shortly.
IPO proceeds
Alpex Solar completed its initial public offering (IPO) during the financial year ended March 31, 2024. The IPO comprised a fresh issue of 64,80,000 equity shares with a face value of Rs 10 each at an issue price of Rs 115 per share, including a share premium of Rs 105, and aggregated Rs 74.52 crore. The shares were listed on the EMERGE platform of the National Stock Exchange of India Limited (NSE), which caters to small and medium enterprises, on February 15, 2024.
The company estimated total IPO offer expenses at Rs 11.59 crore, excluding taxes, which were charged to the Securities Premium Account in accordance with Section 52 of the Companies Act, 2013. According to the financial disclosures, Alpex Solar had earmarked Rs 66.94 crore of net IPO proceeds for utilisation, of which Rs 66.01 crore has been utilised, while about Rs 0.93 crore remained unutilised.
Of the proceeds, the company reported using Rs 19.56 crore for capital expenditure to upgrade and expand its existing solar module manufacturing facility by adding 750 MW of capacity. It also used Rs 20.50 crore for working capital requirements and Rs 13.94 crore for general corporate purposes.
Preferential issue
The company also disclosed the utilisation of funds raised through a preferential allotment in September 2025. It made an offer worth Rs 261.16 crore to identified investors, comprising 10,77,800 equity shares aggregating Rs 130.63 crore and 10,77,000 fully convertible warrants worth Rs 130.53 crore, at an issue price of Rs 1,212 each.
The offer received subscriptions worth Rs 260.17 crore, while Rs 0.99 crore remained unsubscribed and lapsed. The warrants are convertible into an equal number of fully paid-up equity shares within 18 months of allotment.
Alpex Solar received Rs 32.63 crore, representing 25% of the total warrant subscription amount, with the remaining 75% payable by warrant holders on exercise. Of the total proceeds, Rs 97.90 crore represents the balance consideration receivable on exercise of the warrants, and this amount was not available for utilisation as of the reporting date.
Germany’s thyssenkrupp nucera has been awarded a Front-End Engineering and Design (FEED) study for a 260 MW green hydrogen project in India, its first engagement in the country’s hydrogen sector. The FEED contract has been signed with Juno Joule Green Energy Private Limited, which, along with SELECT Energy GmbH, is developing an integrated green hydrogen…
Read More thyssenkrupp nucera wins FEED contract for 260 MW hydrogen project
The Ministry of Power has released the draft National Electricity Data Sharing Framework, 2026, and invited comments from stakeholders within 30 days. The framework seeks to standardise and streamline data sharing across India’s electricity sector, covering generation, transmission, distribution and market operations. Stakeholders can submit comments until July 21, 2026. According to the Ministry, operational…
Read More Power Ministry issues draft National Electricity Data Sharing Framework 2026
INOXGFL Group has expanded its renewable portfolio, with subsidiary Inox Clean Energy completing the acquisition of Vibrant Energy from Macquarie Corporate Holdings for around Rs 5,000 crore. The transaction, completed in four months, adds a 1,337 MW portfolio of solar and hybrid assets. The acquired portfolio supplies power to commercial and industrial (C&I) consumers across…
Read More Inox Clean Energy acquires Vibrant Energy for ~Rs 5,000 crore
NTPC Green Energy Limited (NGEL), a subsidiary of NTPC Limited, has signed a Memorandum of Understanding (MoU) with CtrlS Datacenter Limited to develop renewable energy projects of 2 GW or more for supplying round-the-clock (RTC) renewable power to CtrlS facilities across India.  The agreement was signed in New Delhi on October 31, 2025, by Sarit…
Read More NTPC Green signs MoU with CtrlS Datacenter for 2 GW renewable power supply
Ocean Winds (OW) has submitted its first planning consent application for onshore works to Aberdeenshire Council for the 2 GW Caledonia offshore wind project in Scotland.  This follows the completion of the project’s environmental impact assessment (EIA), which includes detailed studies of both onshore and offshore infrastructure. The onshore component of the Caledonia project includes…
Read More Ocean Winds submits planning application for 2 GW offshore wind farm
India and Bhutan have commissioned the 1,020 MW Punatsangchhu II hydroelectric project, increasing Bhutan’s hydropower capacity by almost 40 per cent. India has also extended a Rs 40 billion concessional line of credit for Bhutan’s energy projects, reflecting deeper cooperation in the power sector. Prime Minister Narendra Modi visited Bhutan from 11 to 12 November…
Read More India and Bhutan inaugurate Punatsangchhu II hydropower project
Your email address will not be published. Required fields are marked *






Subscribe To Our Newsletter
Contact Us
[email protected]
© 2026 Power Peak Digest. All rights reserved.

source

Posted in Renewables | Leave a comment

India's Solar Module Capacity Reaches 116 GW, PLI Projects Add 24 GW – BW Businessworld

India’s Solar Module Capacity Reaches 116 GW, PLI Projects Add 24 GW  BW Businessworld
source

Posted in Renewables | Leave a comment

UK homeowner's heat pump uses 8,000 kWh a year, but 2 meters complicate solar plans – The Cool Down

© 2025 THE COOL DOWN COMPANY. All Rights Reserved. Do not sell or share my personal information. Reach us at hello@thecooldown.com.
“Then you have one standing charge and zero headaches.”
Photo Credit: iStock
One U.K. homeowner had the unusual situation of two electricity meters serving the house. With that setup, they wondered how to best use a potential solar panel and battery system. 
The homeowner turned to Reddit for advice about taking advantage of the separate tariffs, asking whether switching solar panels and batteries between the supplies would be practical and legal.
As the homeowner explained, one of the meters serves the main house, while the other is attached to the power used in an extension on the property. 
The heat pump draws about 8,000 kilowatt-hours a year from the extension’s supply, which has little other usage. Electricity use on the main house meter is roughly 3,000 kilowatt-hours annually.
They considered connecting the solar and batteries to one meter during the summer and then switching them to the other during winter. Summer electricity use on the heat pump‘s supply is very low, and most of the heat pump’s consumption occurs in winter. 
A residential solar panel system can lower electricity bills, and some $0-upfront solar leases may offer savings of hundreds of dollars per month, depending on the household and terms. EasyHome offers a free explorer tool to estimate potential savings and find vetted local installers.
“If I dedicate them all to run the heat pump during winter, it’ll be massively oversized during summer and I’ll be exporting over 90% of what I generate,” the original poster continued. “If I dedicate all the panels to meter 1, I’ll still have a massive bill for running the heat pump. Or I could compromise and do a bit of both but not really impact either bill to any significant degree.”
However, one person suggested a potentially simpler solution. 
With energy prices through the roof, there’s never been a better time to go solar — and EasyHome can help you find the best prices from the best installers in your area.
EasyHome takes the guesswork and headaches out of energy upgrades by showing you estimated savings from a network of vetted local partners. To get started, just enter your ZIP and share a few details about your home — seeing your estimate is really that easy.
“Rewire it so it’s all through one meter,” they said. “Then you have one standing charge and zero headaches.”
While that seems like a sensible approach, the original poster mentioned they wanted to find out whether they were missing an opportunity to save money with the unconventional metering system. 
Regardless of the metering arrangement in your home, solar panels and battery storage are an effective one-two punch to slash energy bills, become more energy independent, and reduce reliance on grid-provided power, which still heavily relies on polluting fuel sources. 
For households weighing energy storage alongside panels, EasyHome can help. Combining solar with the right battery setup can help manage electricity costs and provide backup power during outages.
Other U.K. homeowners are also trying to match heat pumps, solar panels, and batteries to their electricity needs. 
• One homebuyer weighed heat pumps and batteries for an affordable all-electric renovation.
• At one home, a 32kWh backup battery was able to run a heat pump for 16 hours.
• A battery-only electricity setup was explored after the owner ruled out solar panels.
• A homeowner’s 16kWh battery fell short of daily needs, but switching tariffs could cost more.
• U.K. solar users said falling electricity export rates are making home batteries increasingly important.
Get TCD’s free newsletters for easy tips, smart advice, and a chance to earn $5,000 toward home upgrades. To see more stories like this one, change your Google preferences here.
© 2025 THE COOL DOWN COMPANY. All Rights Reserved. Do not sell or share my personal information. Reach us at hello@thecooldown.com.

source

Posted in Renewables | Leave a comment

R2R Green Energy Strengthens Its Position as a Flexible Solar Panel Manufacturer – EIN News

R2R Green Energy Strengthens Its Position as a Flexible Solar Panel Manufacturer  EIN News
source

Posted in Renewables | Leave a comment

India's solar manufacturing hits 116 GW as PLI scheme boosts domestic output – The Economic Times

India’s solar module manufacturing capacity has expanded significantly due to the Production Linked Incentive scheme. The country has seen a reduction in imports while simultaneously increasing its exports of solar PV modules. Approximately 20.7 percent of current manufacturing capacity can be linked to PLI-supported projects, reflecting strong investment mobilization. However, employment generation and production-related outcomes continue to evolve as facilities scale up.

(Catch all the Business News, Breaking News and Latest News Updates on The Economic Times.)
Subscribe to The Economic Times Prime and read the ET ePaper online.
(Catch all the Business News, Breaking News and Latest News Updates on The Economic Times.)
Subscribe to The Economic Times Prime and read the ET ePaper online.

Hot on Web
In Case you missed it
Top Searched Companies
Top Calculators
Top Commodities
Top Prime Articles
Top Story Listing
Top Definitions
Top Slideshow
Private Companies
Latest News
Follow us on:
Find this comment offensive?
Choose your reason below and click on the Report button. This will alert our moderators to take action
Reason for reporting:
Your Reason has been Reported to the admin.
Log In/Connect with:
Will be displayed
Will not be displayed
Will be displayed
Stories you might be interested in

source

Posted in Renewables | Leave a comment

LONGi at COP31: Four Enabling Pathways to Advance Global Green Development – ACROFAN USA

LONGi at COP31: Four Enabling Pathways to Advance Global Green Development  ACROFAN USA
source

Posted in Renewables | Leave a comment

Localising Critical PV Components: Why Domestic Junction Box Manufacturing Matters to India’s Solar Supply Chain – Energetica India Magazine

Junction boxes illustrate that India can move quickly from import dependence to competitive domestic supply in mid-stream components once policy signals and market demand align.
November 16, 2026. By News Bureau

DEK & Mavericks’ Ajay Rawat Explains the Future of Renewable EPC

IB Solar Targets 1 GW Solar Cell Capacity and BESS Expansion, Says Abhinav Mahajan

Solis’ Honey Raza Explains the Shift Towards Solar-Plus-Storage Solutions in India

Credence Solar’s Jinto Joseph Explains the Company’s Manufacturing Growth Strategy

Mohammed Saif Zaveri, JRST Technology, Explains Journey Towards Domestic Ingot Manufacturing

source

Posted in Renewables | Leave a comment

India's solar module capacity jumps 15-fold to 116 GW on PLI push – IANS LIVE

New Delhi, Nov 16 (IANS) Projects supported under the Production Linked Incentive (PLI) scheme have contributed around 24 GW to India’s solar module manufacturing capacity, which has expanded nearly 15-fold from about 8 GW to nearly 116 GW, according to a report by NITI Aayog.
The report said around 20.7 per cent of India’s current solar photovoltaic (PV) module manufacturing capacity is directly attributable to PLI-supported projects.
It also highlighted that the High Efficiency Solar PV Modules PLI scheme has an outlay of Rs 24,000 crore and aims to promote large-scale domestic production, encourage advanced technologies and reduce dependence on imports.
Cumulative investment under the scheme reached Rs 64,873 crore by March this year.
The expansion in capacity has coincided with a decline in imports and a rise in exports. Solar PV module imports fell from around $4.35 billion in 2023-24 to $2.15 billion in 2024-25.
Exports rose from $83 million in 2021-22 to $1.97 billion in 2023-24 before moderating to around $1.12 billion in 2024-25.
The scheme has also encouraged manufacturers to increase domestic sourcing by linking incentives to local value addition to develop a more integrated solar manufacturing ecosystem.
“Overall, the Solar PV PLI Scheme demonstrates strong early outcomes in investment mobilisation, manufacturing capacity creation, import substitution and export expansion,” the report said.
However, it flagged pressure from falling global module prices, partly due to excess manufacturing capacity and aggressive pricing by Chinese producers.
The scheme’s long-term effectiveness would depend on manufacturers achieving higher domestic value addition, remaining globally cost-competitive, developing capabilities across the wider value chain and sustaining export growth amid changing global market conditions, according to the report.
Additionally, the PLI framework has emerged as one of the country’s most significant industrial policy interventions, with approved applications standing at 791 across 14 sectors, cumulative investment exceeding Rs 2.58 lakh crore and cumulative production/sales crossing Rs 23.79 lakh crore by June 30, according to the government.
–IANS
ag/
IANS India Private Limited
D5-6, Third Floor, Block D
Sector-3, Noida, Uttar Pradesh
Phone: +91-120-4822400, 4822415, 4822416
Email: dakul.s@ians.in, marketing@ians.in

source

Posted in Renewables | Leave a comment

ClearVue wins Singapore solar project – The Australian

ClearVue wins Singapore solar project  The Australian
source

Posted in Renewables | Leave a comment

Homeowner says solar installer folded and inverter maker won't take calls about a suspected failure – The Cool Down

© 2025 THE COOL DOWN COMPANY. All Rights Reserved. Do not sell or share my personal information. Reach us at hello@thecooldown.com.
They said they needed an EIN number before their query could be handled.
Photo Credit: iStock
An apparently defunct solar panel installer and an unreachable equipment manufacturer left one homeowner unsure where to turn for help with a suspected inverter failure.
The homeowner’s contract with a solar installer covered both panels and an inverter, according to their Reddit post.
“The inverter seems to be broken, and we were hoping we could get a technician to look at it or set the wheels in motion to get it replaced,” they wrote.
With the installer apparently out of business, the homeowner tried contacting the inverter manufacturer, but they had been unable to speak to anyone. They said they needed an EIN number before their query could be handled.
“Does anyone have any experience with something like this?” they asked. “Can anyone provide suggestions as to what I might be able to do?”
A solar installer in the thread said they dealt with a similar case. Their customer also needed an inverter swap, but because they were a qualified solar professional with an EIN number, they had no trouble getting the support service on the phone.
That led one commenter to suggest finding a technician willing to work on a system installed by a different company.
Meanwhile, another noted that when calling the inverter company, they should select an option saying they are a homeowner, which would put them through to an AI agent. From there, they should be able to get transferred to a representative. 
With energy prices through the roof, there’s never been a better time to go solar — and EasyHome can help you find the best prices from the best installers in your area.
EasyHome takes the guesswork and headaches out of energy upgrades by showing you estimated savings from a network of vetted local partners. To get started, just enter your ZIP and share a few details about your home — seeing your estimate is really that easy.
While stories like this might put some off a solar installation, there are still plenty of reputable companies around, and the technology can provide significant savings on energy bills and reduce reliance on grid-provided energy. For example, some $0-upfront solar leases may save owners hundreds of dollars per month, depending on the home and arrangement. EasyHome offers a free explorer tool to estimate possible savings and find vetted local installers.
A manufacturer-specific forum could offer more targeted guidance, commenters suggested. One also advised finding out whether the inverter model was still available.
For homeowners evaluating a new setup, EasyHome also offers battery storage exploration options. Comparing solar and battery configurations can help households manage electricity costs and provide backup power during outages, while keeping equipment and service needs part of the conversation.
Other solar owners have also struggled to get help with equipment problems after companies closed or installers declined repairs.
• After their solar company folded, a homeowner received a free inverter but faced installation hurdles.
• A New York homeowner discovered 24 incorrect solar inverters, prompting upgrades and a $2,500 offer.
• A homebuyer’s underperforming solar array produced one-third of the expected power, while installers declined help.
• In Rhode Island, apparently functional solar equipment produced just 5 kWh despite clear skies.
• One solar owner’s system continued working without internet despite the manufacturer’s bankruptcy.
Get TCD’s free newsletters for easy tips, smart advice, and a chance to earn $5,000 toward home upgrades. To see more stories like this one, change your Google preferences here.
© 2025 THE COOL DOWN COMPANY. All Rights Reserved. Do not sell or share my personal information. Reach us at hello@thecooldown.com.

source

Posted in Renewables | Leave a comment

EDP Renewables breaks ground on 250 MW Arkansas solar farm backed by Meta – Energies Media

Energies Media
The clean energy transition has resulted in a number of companies that are not operating in the energy industry becoming financially involved with energy companies and backing them as they execute energy projects that will provide clean electricity for the general population. The reason for this, especially from the United States’ perspective, is that companies understand the importance of the nation reaching its clean energy targets and reducing carbon emissions, and so are actively participating in assisting the nation reach its targets. It was recently revealed that EDP Renewables broke ground on a 250 MW Arkansas solar farm backed by Meta.
Meta is one of the most recognizable companies in the world focused on technology and advancing social media platforms. However, as Artificial Intelligence becomes more sophisticated, the demand for electricity is putting companies in a position where they need to be involved in energy projects that can guarantee a reliable supply of electricity.
EDP Renewables is a global leader in renewable energy and the fourth largest wind energy producer. Importantly, the company is not just focused on wind generation, as it has also been involved in groundbreaking solar energy projects over the years.
EDP Renewables North America is headquartered in Houston, Texas. It owns 61 wind farms, 29 solar parks, and energy storage systems throughout North America. According to reports, the company has developed more than 12,900 megawatts (MW). It operates more than 12,300 MW of onshore utility-scale renewable energy projects.
According to a press release from EDP Renewables, the company recently celebrated the groundbreaking of Cypress Knee Solar, a 250-megawatt solar energy project in Chicot County, Arkansas. The project is supported by a long-term power purchase agreement with Meta. It represents a significant investment in Arkansas’ energy future, local economy, and energy infrastructure.
It is interesting to witness how much the solar energy industry has evolved to the point where massive companies are investing millions of dollars in facilities that were once deemed a risky investment. When operational, the Cypress Knee Solar facility is expected to help deliver new power generation to the grid while supporting continued economic growth in the region.
Because of how massive a project this is, it is expected to be completed by 2028 and generate an estimated $25 million in new revenue for Chicot County over its lifetime. With more than 1,000 employees, EDPR NA’s highly qualified team has a proven capacity to execute projects across the continent.
EDP Renewables has accumulated a tremendous amount of success, which means that every project the company pursues must push boundaries and further improve its portfolio. Breaking ground at Cypress Knee Solar marks an essential milestone for the project and for Arkansas’ growing role in America’s energy future. The United States deserves huge credit for fostering an environment where each state is incentivized to participate in the clean energy transition and help the nation reach its set objectives.
As energy demand continues to rise, projects like Cypress Knee Solar help strengthen grid reliability while creating jobs, generating meaningful local revenue, and delivering long-term benefits to the communities that host them. The company is pleased to be partnering with Meta and local stakeholders to advance new energy infrastructure that supports economic growth and American energy independence.
For Meta, the project is integral as it supports the company’s commitment to matching 100% of its annual electricity use with clean and renewable energy generation. Once operational, the facility will contribute tax revenue that can help fund schools, infrastructure improvements, emergency services, and other community priorities.   
Prince is a versatile writer focused on energy, automotive, environmental, and general news topics. He makes complex technical and policy issues clear, engaging, and accessible for a broad audience.
Prince is a versatile writer focused on energy, automotive, environmental, and general news topics. He makes complex technical and policy issues clear, engaging, and accessible for a broad audience.
Prince is a versatile writer focused on energy, automotive, environmental, and general news topics. He makes complex technical and policy issues clear, engaging, and accessible for a broad audience.

source

Posted in Renewables | Leave a comment

India's solar module capacity reaches 116 GW as PLI scheme adds 24 GW – BusinessLine

 -318.56
 -155.05
+ 69.00
+ 525.00
 -2,124.00
 -318.56
 -155.05
 -155.05
+ 69.00
+ 69.00
+ 525.00
Interactives
Interactive reads from
the businessline desk
India’s solar module manufacturing capacity has expanded to nearly 116 GW, with PLI-supported projects contributing around 24 GW. | Photo Credit: iStockphoto
Projects supported by the Production Linked Incentive (PLI) scheme have contributed around 24 GW to India’s solar module manufacturing capacity, which has expanded nearly 15-fold from approximately 8 GW to nearly 116 GW, according to a report by NITI Aayog.
The report stated that approximately 20.7 per cent of India’s current solar photovoltaic (PV) module manufacturing capacity is directly attributable to PLI-supported projects, highlighting the scheme’s contribution to strengthening domestic manufacturing capabilities.
The High Efficiency Solar PV Modules PLI scheme has an outlay of Rs 24,000 crore and aims to promote large-scale domestic production, encourage advanced technologies and reduce dependence on imports. Cumulative investment under the scheme reached Rs 64,873 crore by March 2026.
The expansion in manufacturing capacity has coincided with a decline in imports and an increase in exports. Solar PV module imports fell from approximately USD 4.35 billion in 2023-24 to USD 2.15 billion in 2024-25.
Exports rose from USD 83 million in 2021-22 to USD 1.97 billion in 2023-24, before remaining relatively strong at around USD 1.12 billion in 2024-25, the report said.
It noted that the scheme had also encouraged manufacturers to increase domestic sourcing by linking incentives to the level of local value addition. The report said this approach was aimed at developing a more integrated solar manufacturing ecosystem within the country.
“Overall, the Solar PV PLI Scheme demonstrates strong early outcomes in investment mobilisation, manufacturing capacity creation, import substitution and export expansion,” the report said.
However, the assessment noted that employment generation and production-related outcomes were still evolving, as several manufacturing facilities were in the process of scaling up capacity.
It also flagged pressure from falling global module prices, partly due to excess manufacturing capacity and aggressive pricing by Chinese producers. Supply constraints affecting critical materials and China’s continued dominance in global solar supply chains were identified as additional challenges.
The report said the scheme’s long-term effectiveness would depend on manufacturers achieving higher domestic value addition, remaining globally cost-competitive, developing capabilities across the wider value chain and sustaining export growth amid changing global market conditions.
Published on November 16, 2026
Copyright© 2026, THG PUBLISHING PVT LTD. or its affiliated companies. All rights reserved.
BACK TO TOPArrow Icon
Comments have to be in English, and in full sentences. They cannot be abusive or personal. Please abide by our community guidelines for posting your comments.
We have migrated to a new commenting platform. If you are already a registered user of TheHindu Businessline and logged in, you may continue to engage with our articles. If you do not have an account please register and login to post comments. Users can access their older comments by logging into their accounts on Vuukle.
Terms & conditions  |  Institutional Subscriber

source

Posted in Renewables | Leave a comment

PLI helps boost India's solar capacity to nearly 116 GW – NewsBytes

PLI helps boost India’s solar capacity to nearly 116 GW  NewsBytes
source

Posted in Renewables | Leave a comment

'Orwellian' footpath warning as rural solar farm opposition intensifies – Beccles & Bungay Journal

Share
Share
Find, save and share Public Notices that affect you in the area.
The Public Notice Portal carries statutory public notices published in local newspapers and is the fastest and most effective way of finding out what is happening in YOUR neighbourhood.
A planned solar farm capable of powering thousands of homes is facing fresh criticism, with opponents claiming walkers could be forced through an “Orwellian” corridor lined with security fencing and CCTV cameras.
The latest concerns centre on public footpaths crossing a proposed 130-acre solar farm at Chediston Hall, near Halesworth.
Campaigners have highlighted a holding objection submitted by Suffolk County Council Public Rights of Way Team, which says the scheme would have a detrimental impact on the existing network of footpaths.
View of Herne Hill Farmhouse and the development site on approach from the East along Footpath 8 (Image: East Suffolk Council)
The objection raises concerns about the proposed siting of a substation near Wissett Footpath Three, the potential for the route to become a fenced corridor, and a lack of detail on crossings, signage, and safety measures.
The authority said it would be prepared to review its objection if those matters were addressed.
The solar farm, proposed by Neo Environmental on behalf of Sky UK Development Ltd, would generate enough electricity to meet the annual needs of about 13,300 homes.
The scheme would neighbour the existing solar farm and be created to the west, north, and east of Chediston Hall (Image: Neo Environmental)
Among the raft of objections lodged against the plans, one local warned the development would transform one footpath from a countryside walk to an “industrial corridor”.
One objector said the route would be “sandwiched between security fencing on either side, with CCTV cameras for that added Orwellian feeling”.
They added: “This represents a vast, tragic, and devastating loss of amenity and access to open space currently enjoyed by the residents of Chediston, Halesworth and the surrounding area.”
Access would be from the south via the existing road that serves Chediston Hall and links to Chediston Street / B1123. (Image: Google Maps)
The concerns echo observations made by East Suffolk Council’s landscape team, who acknowledge that footpaths running through the site are particularly vulnerable to change and warned against “tunnelling” users through enclosed routes where they currently enjoy far-reaching countryside views.
Opponents also argue one of the most important aspects of the scheme remains unanswered – how the electricity generated would reach the National Grid.
Planning documents state the solar farm would connect to Halesworth Main substation via a new underground cable, but add that the precise route “is unconfirmed at this stage” and “does not form part of the proposals subject to this planning application”.
Share
This website and associated newspapers adhere to the Independent Press Standards Organisation’s Editors’ Code of Practice. If you have a complaint about the editorial content which relates to inaccuracy or intrusion, then please contact the editor here. If you are dissatisfied with the response provided you can contact IPSO here
© 2001-2026. The Beccles & Bungay Journal is owned and operated by Newsquest Media Group Ltd, an audited local newspaper network.
Visit newsquest.co.uk to view our policies, terms and legal agreements.
The Echo Building, 18 Albert Road, Bournemouth, England BH1 1BZ. Registered in England & Wales | 01676637
Data returned from the Piano ‘meterActive/meterExpired’ callback event.
As a subscriber, you are shown 80% less display advertising when reading our articles.
Those ads you do see are predominantly from local businesses promoting local services.
These adverts enable local businesses to get in front of their target audience – the local community.
It is important that we continue to promote these adverts as our local businesses need as much support as possible during these challenging times.

source

Posted in Renewables | Leave a comment

PLI-backed projects contribute 24 GW to India's 116 GW solar manufacturing capacity: NITI Aayog – Big News Network.com

New Delhi [India], November 16 (ANI): Projects supported by the Production Linked Incentive (PLI) scheme have contributed around 24 GW to India’s solar module manufacturing capacity, which has expanded nearly 15-fold from approximately 8 GW to nearly 116 GW, according to a report by NITI Aayog.
The report stated that approximately 20.7 per cent of India’s current solar photovoltaic (PV) module manufacturing capacity is directly attributable to PLI-supported projects, highlighting the scheme’s contribution to strengthening domestic manufacturing capabilities.
The High Efficiency Solar PV Modules PLI scheme has an outlay of Rs 24,000 crore and aims to promote large-scale domestic production, encourage advanced technologies and reduce dependence on imports. Cumulative investment under the scheme reached Rs 64,873 crore by March 2026.
The expansion in manufacturing capacity has coincided with a decline in imports and an increase in exports. Solar PV module imports fell from approximately USD 4.35 billion in 2023-24 to USD 2.15 billion in 2024-25.
Exports rose from USD 83 million in 2021-22 to USD 1.97 billion in 2023-24, before remaining relatively strong at around USD 1.12 billion in 2024-25, the report said.
It noted that the scheme had also encouraged manufacturers to increase domestic sourcing by linking incentives to the level of local value addition. The report said this approach was aimed at developing a more integrated solar manufacturing ecosystem within the country.
“Overall, the Solar PV PLI Scheme demonstrates strong early outcomes in investment mobilisation, manufacturing capacity creation, import substitution and export expansion,” the report said.
However, the assessment noted that employment generation and production-related outcomes were still evolving, as several manufacturing facilities were in the process of scaling up capacity.
It also flagged pressure from falling global module prices, partly due to excess manufacturing capacity and aggressive pricing by Chinese producers. Supply constraints affecting critical materials and China’s continued dominance in global solar supply chains were identified as additional challenges.
The report said the scheme’s long-term effectiveness would depend on manufacturers achieving higher domestic value addition, remaining globally cost-competitive, developing capabilities across the wider value chain and sustaining export growth amid changing global market conditions. (ANI)

ANI
16th November 2026, 14:35 GMT+11
New Delhi [India], November 16 (ANI): Projects supported by the Production Linked Incentive (PLI) scheme have contributed around 24 GW to India’s solar module manufacturing capacity, which has expanded nearly 15-fold from approximately 8 GW to nearly 116 GW, according to a report by NITI Aayog.
The report stated that approximately 20.7 per cent of India’s current solar photovoltaic (PV) module manufacturing capacity is directly attributable to PLI-supported projects, highlighting the scheme’s contribution to strengthening domestic manufacturing capabilities.
The High Efficiency Solar PV Modules PLI scheme has an outlay of Rs 24,000 crore and aims to promote large-scale domestic production, encourage advanced technologies and reduce dependence on imports. Cumulative investment under the scheme reached Rs 64,873 crore by March 2026.
The expansion in manufacturing capacity has coincided with a decline in imports and an increase in exports. Solar PV module imports fell from approximately USD 4.35 billion in 2023-24 to USD 2.15 billion in 2024-25.
Exports rose from USD 83 million in 2021-22 to USD 1.97 billion in 2023-24, before remaining relatively strong at around USD 1.12 billion in 2024-25, the report said.
It noted that the scheme had also encouraged manufacturers to increase domestic sourcing by linking incentives to the level of local value addition. The report said this approach was aimed at developing a more integrated solar manufacturing ecosystem within the country.
“Overall, the Solar PV PLI Scheme demonstrates strong early outcomes in investment mobilisation, manufacturing capacity creation, import substitution and export expansion,” the report said.
However, the assessment noted that employment generation and production-related outcomes were still evolving, as several manufacturing facilities were in the process of scaling up capacity.
It also flagged pressure from falling global module prices, partly due to excess manufacturing capacity and aggressive pricing by Chinese producers. Supply constraints affecting critical materials and China’s continued dominance in global solar supply chains were identified as additional challenges.
The report said the scheme’s long-term effectiveness would depend on manufacturers achieving higher domestic value addition, remaining globally cost-competitive, developing capabilities across the wider value chain and sustaining export growth amid changing global market conditions. (ANI)

ASSOCIATES
BIG NEWS NETWORK.COM
PRODUCTS & SERVICES
FOLLOW US
Copyright © 1998-2025 Big News Network All rights reserved. ISSN: 2616-6917

source

Posted in Renewables | Leave a comment

Building More Solar Energy Sources Means Rethinking Land Use For Agriculture And Conservation – FlaglerLive

FlaglerLive
No Bull, no Fluff, No Smudges
| | Leave a Comment
By Adam Gallaher
The state of New York could meet its goal of building 46 gigawatts of large-scale solar by midcentury, but not without making difficult choices in how land is used across the state.
That’s the overall finding of an analysis several colleagues and I have made in that state. It’s an issue that other states, and the U.S. as a whole, are facing as they seek to shift electricity generation from fossil fuels to renewable sources, such as wind and solar.
The question of land use arises because power plants that burn coal and natural gas can produce large amounts of electricity from relatively small areas of land – but solar requires more space to generate the same amount of electricity.
That means deciding which land to build on, and why.

It’s often convenient to build solar projects in pastures and hay fields, for instance. But the dairy industry and agriculture more generally are key components in New York state’s economy, and building in agricultural areas would leave less land for those important industries. However, protecting farmland could lead solar developers to consider using existing forests. Yet forests not only soak up carbon dioxide from the atmosphere, helping reduce the effects of fossil-fuel emissions that are changing the global climate, but also support biodiversity by providing important habitat for wildlife. Basically, deciding to prioritize one type of land use means shifting that amount of development pressure to land now being used for other purposes.
As a geographer, I study these trade-offs and their inherent tensions to better understand how to determine the best way to use a particular piece of land to reduce carbon emissions. One of the primary obstacles to building more large-scale solar is the drawn-out debate over where to put it. Typical decision-making factors include farmland loss, wildlife habitat, rural landscapes and who ultimately uses the energy. The results will determine who benefits from the expansion of renewable energy and who bears the ecological and social costs.

Solar energy is the fastest-growing source of electricity in the U.S., with nearly 397 gigawatts waiting to come on line as of 2025. Of that, 70 gigawatts of generating capacity is expected to come on line in 2026 and 2027 – on top of the nearly 148 gigawatts operating at the end of 2025.
This represents progress toward reducing carbon emissions but also requires vast tracts of repurposed land. For example, a 100-megawatt solar project could require approximately 417 acres of land, roughly the same area as 316 American football fields, based on a conservative power density of 0.24 megawatts per acre. Therefore, the 70 gigawatts of solar energy expected to come on line in the next two years will require just over 320,000 acres of land, or about 242,424 football fields, about 53% of which is expected to displace farmland. Additionally, those projects are expected to replace roughly 22,000 acres of forest and just under 10,000 acres of wetlands.

Energy, agriculture and conservation don’t have to be mutually exclusive uses of land. Instead, land can be managed more efficiently by integrating multiple uses, commonly referred to as colocation.
Grazing livestock or growing crops underneath or between rows of raised solar panels, known as agrivoltaics, is one way to keep land available for agriculture while also generating electricity.
Another approach, known as ecovoltaics, involves designing solar projects to equally support renewable energy and ecosystem services, such as providing habitat for pollinators or reducing evaporation in stressed arid ecosystems.
Another emerging alternative involves solar panels that are constructed to float on water rather than being mounted on land.

These approaches won’t work everywhere, but they demonstrate that, with careful thought, more renewable energy doesn’t have to hurt the environment. Specific project proposals, evaluations by local planning boards and input from the public can consider more than the costs and electricity generated from new projects. They can also take into account how plants and animals will be affected and the degree to which the land use really must change to accommodate the addition of solar panels.
As New York, and the U.S. as a whole, seeks to achieve renewable energy goals to help fight climate change, I believe discussions will be more productive if they expand beyond just how much generating capacity can be built, but where and how it is constructed.

Adam Gallaher is Assistant Professor of Geography and Environmental Studies at Central Michigan University.

Your email address will not be published. Required fields are marked *








Log in

source

Posted in Renewables | Leave a comment

LONGi at COP31: Four Enabling Pathways to Advance Global Green Development – StreetInsider

LONGi at COP31: Four Enabling Pathways to Advance Global Green Development  StreetInsider
source

Posted in Renewables | Leave a comment

‘Delhi adopting clean energy’: Government passes halfway mark for solar rooftop project – The Indian Express

‘Delhi adopting clean energy’: Government passes halfway mark for solar rooftop project  The Indian Express
source

Posted in Renewables | Leave a comment

Developer seeks 980,000 PV panels for Queensland solar and battery project – pv magazine Australia

Renewables developer Central Queensland Power (CQP) has launched an expressions of interest (EOI) process seeking suppliers for the proposed Wooderson solar and battery energy storage project being developed near the Queensland industrial hub of Gladstone.
The project, planned for a site at Mount Alma, approximately 40 kilometres southwest of Gladstone, includes a 450 MW solar facility along with a 450 MW DC-coupled battery energy storage system (BESS) with up to 3,600 MWh of storage.
CQP, a joint venture between Sydney-based Energy Estate and the Australian arm of United Kingdom-headquartered clean energy company RES, has now opened an EOI through Gateway by ICN.
Anticipated supply chain requirements span civil and electrical balance of plant works, equipment supply, high-voltage infrastructure, transport, logistics, commissioning and skilled labour.
The developer is aiming to secure the supply of about 980,000 solar panels, a 450 MW BESS, substation, switching yard, 275 kV transmission connection, electrical infrastructure, access roads and construction facilities.
Procurement for lead construction contractors is expected to progress later this year with construction currently targeted for the first quarter of 2028, with completion expected by December 2030, subject to approvals, financing and investment decisions. Small works procurement is expected to begin approximately six to nine months before construction.
CQP estimates the Wooderson project will generate up to 680 jobs during the construction phase, and, once operational, would deliver about 1,300 GWh of renewable energy into the National Electricity Market a year.
The project recently secured the first of three required planning approvals, covering a section of the proposed overhead transmission line within the Callide Infrastructure Corridor State Development Area (CICSDA). The project also holds an earlier environmental clearance from the Australian government, which determined it was not a controlled action under the EPBC Act.
The project needs to also go through the Queensland government State Assessment and Referral Agency (SARA) for the solar farm and ancillary infrastructure including the BESS, and the Gladstone Regional Council for sections of the proposed overhead transmission line and switchyard located outside the CICSDA.

This content is protected by copyright and may not be reused. If you want to cooperate with us and would like to reuse some of our content, please contact: [email protected].
Comments
Please login to comment
The new issue of pv magazine Global is out now!
Available in print and digital – get your copy today!
Monday, November 23, 2026
11:00 am – 12:00 pm CEST, Berlin, Paris, Madrid

You have no items in your basket.

source

Posted in Renewables | Leave a comment

PLI-backed projects contribute 24 GW to Indias 116 GW solar manufacturing capacity: NITI Aayog – The Tribune

New Delhi [India], November 16 (ANI): Projects supported by the Production Linked Incentive (PLI) scheme have contributed around 24 GW to India’s solar module manufacturing capacity, which has expanded nearly 15-fold from approximately 8 GW to nearly 116 GW, according to a report by NITI Aayog.
The report stated that approximately 20.7 per cent of India’s current solar photovoltaic (PV) module manufacturing capacity is directly attributable to PLI-supported projects, highlighting the scheme’s contribution to strengthening domestic manufacturing capabilities.
The High Efficiency Solar PV Modules PLI scheme has an outlay of Rs 24,000 crore and aims to promote large-scale domestic production, encourage advanced technologies and reduce dependence on imports. Cumulative investment under the scheme reached Rs 64,873 crore by March 2026.
The expansion in manufacturing capacity has coincided with a decline in imports and an increase in exports. Solar PV module imports fell from approximately USD 4.35 billion in 2023-24 to USD 2.15 billion in 2024-25.

Exports rose from USD 83 million in 2021-22 to USD 1.97 billion in 2023-24, before remaining relatively strong at around USD 1.12 billion in 2024-25, the report said.

It noted that the scheme had also encouraged manufacturers to increase domestic sourcing by linking incentives to the level of local value addition. The report said this approach was aimed at developing a more integrated solar manufacturing ecosystem within the country.
“Overall, the Solar PV PLI Scheme demonstrates strong early outcomes in investment mobilisation, manufacturing capacity creation, import substitution and export expansion,” the report said.

However, the assessment noted that employment generation and production-related outcomes were still evolving, as several manufacturing facilities were in the process of scaling up capacity.
It also flagged pressure from falling global module prices, partly due to excess manufacturing capacity and aggressive pricing by Chinese producers. Supply constraints affecting critical materials and China’s continued dominance in global solar supply chains were identified as additional challenges.
The report said the scheme’s long-term effectiveness would depend on manufacturers achieving higher domestic value addition, remaining globally cost-competitive, developing capabilities across the wider value chain and sustaining export growth amid changing global market conditions. (ANI)

(This content is sourced from a syndicated feed and is published as received. The Tribune assumes no responsibility or liability for its accuracy, completeness, or content.)
THE TRIBUNE, India’s oldest, daily English-language newspaper, was first published on February 2, 1881, in Lahore (now in Pakistan), and save for 40 days in the immediate aftermath of Partition, has come out every day over the last 145 years. THE TRIBUNE was started by Sardar Dyal Singh Majithia, a public-spirited philanthropist of the time. The newspaper is run by a five-member Trust, which is chaired by Shri N N Vohra, former Governor of J&K State (2008-2018); as well as Justice S S Sodhi, former Chief Justice of the Allahabad High Court; Shri Gurbachan Jagat, former Governor of Manipur; Lt Gen. Shamsher Singh Mehta, former Western Army Commander; Shri Paramjit Singh Patwalia, Senior Advocate in the Supreme Court.

THE TRIBUNE is free, objective, and independent. Restraint and moderation, rather than agitational language, are the hallmarks of the paper.

The Tribune has two sister publications, Punjabi Tribune (in Punjabi) and Dainik Tribune (in Hindi).
Remembering Sardar Dyal Singh Majithia

source

Posted in Renewables | Leave a comment

Should Homeowners Still Invest In Home Solar Power Now That The Tax Credit Is Gone? – SlashGear

Investing in a home solar array became less attractive when the federal tax credit on energy-efficient installations ended in 2025. Even as panel production prices (for all different types of consumer solar panels) have continued to fall, the average quote for even a modest build in the United States can push above $20,000. As the leading state in solar projects, California has been at the brunt of a further decrease in returns as the Net Energy Metering 3.0 scheme in 2023 reduced prices for midday solar generation in the hopes of getting more residential battery projects into gear to supply the evening peak hours.
A new wave of tariffs coming into effect in December will establish high floor prices on a key solar panel component, potentially pushing the breakeven period of a solar-only installation right up to if not past its typical useful life. As states have migrated their solar-based credit and rebate programs towards battery generation events, you’re probably better off going with a solar and battery project for your home than a pure solar one.
Solar marketplace research firm EnergySage currently estimates project breakeven points running between 8 years in a state like California to 24 years in Alabama for an average-size build respective to each state. Many states fall within the 10- to 15-year timeframe, including Illinois, New York, Pennsylvania, and Texas. Keep in mind that these panels have an expected lifespan of anywhere between 20 and 35 years, depending on how new the installation is. These calculations do not include any applicable solar installation incentives, such as they are available from states.
Expect to wait longer for your payback if you’re installing after December 4 as a wave of so-called Section 232 tariffs (which have also been used against steel and other metals used in home improvement tools from the likes of DeWalt and Craftsman) issued in August concerning polysilicon, a key component of photovoltaic panels, comes into effect. Imports of finished solar modules will be subject to a minimum sale price of 38 cents per watt plus a value-added tax of up to 15%. 
Disregarding the VAT, this represents a 20% to 50% increase from today’s prices at common sources. Installers could decide to cut their non-fungible overhead — elements including labor, marketing, and margin that make up nearly half of the bill, according to EnergySage — to pass on a lower increase, at least initially. Still, even a single-digit percentage premium could mean an extra $1,000 or $2,000 to your bill.
Many states and utilities now offer installation and generation incentives for residential stored power projects. For example, energy providers in Massachusetts offer up to $1,375 a year for up to 60 summertime activations at 5kW output. In neighboring Rhode Island, the state will rebate builds at $250 per kilowatt-hour ($500 for property owners with eligible incomes) for the first 25kW of capacity and $175/kWh for further capacity on larger plots up to 250kW. 
Tesla’s Powerwall series of batteries are a go-to choice (though not the only one) for many proprietors and can make sense as part of an integrated setup with a smaller solar array for about the same price as going solar-only. You’ll want to evaluate your own usage, brush up on incentive programs available to you, and then match those specs to products on the market to maximize your potential returns. This is all on top of the extra breathing room and peace of mind you get if and when a grid outage occurs — keeping the fridge running means you can tack on a trip’s worth of groceries to your overall savings.

source

Posted in Renewables | Leave a comment

PLI-backed projects contribute 24 GW to India's 116 GW solar manufacturing capacity: NITI Aayog – ANI News

PLI-backed projects contribute 24 GW to India’s 116 GW solar manufacturing capacity: NITI Aayog  ANI News
source

Posted in Renewables | Leave a comment

California shopper finds a generator listed as 'CARB compliant' but can't get it shipped – The Cool Down

© 2025 THE COOL DOWN COMPANY. All Rights Reserved. Do not sell or share my personal information. Reach us at hello@thecooldown.com.
The shopper’s ZIP code proved to be a barrier at multiple retailers.
Photo Credit: iStock
A California shopper thought they had found a small generator at the right price, only to discover that getting it delivered was another challenge entirely.
The shopper’s ZIP code proved to be a barrier at multiple retailers, thanks to California’s stricter rules for generators.
To charge their battery station, the shopper needed a dual-fuel inverter generator rated for 2,500 to 3,000 watts. They asked Reddit’s r/Generator community for help finding one.
“Lowe’s says it is CARB compliant,” the original poster wrote, “yet I am restricted from ordering it.”
When a commenter suggested buying directly from the manufacturer, the shopper explained that they had already tried that without success.
“Wen won’t ship to my zip,” they said. The shopper added that the problem extended beyond the manufacturer. “I’ve run into that with every retailer. Guess I have a road trip in my future.”
💡These best-sellers from Quince deliver affordable, sustainable luxury for all
Starting at $50
Starting at $99
Starting at $60
Starting at $80
One commenter disputed the preferred model’s compliance status, while others reported successfully purchasing different generators in California. The shopper wanted a relatively small machine that fit their budget, but several suggested options didn’t meet their power needs.
An off-grid owner said they used their Champion 2,500-watt dual-fuel generator almost daily after buying it on sale for $450. Another commenter pointed to a $465 Walmart listing for the Pulsar PG2200BiS.
One commenter said they had bought two Champion 2500 dual-fuel generators in California and used them separately or together. They recommended the model available at Tractor Supply.
Another shared a Harbor Freight listing for a California-compliant, 4,200-watt dual-fuel inverter generator. A separate commenter recommended checking the retailer’s website for local stock, citing a $550 Black Friday sale price for a Predator 4,200-watt model.
While the Harbor Freight option produced more power than the original poster needed, the Champion recommendation matched the lower end of their range. Another suggestion was to try a local lawn equipment dealer carrying the Honda EU3200.
California sales restrictions have left other generator shoppers searching for options, too. These stories cover compliance changes and sales restrictions.
• One generator model lost its California-compliant option, fueling fears that the model could disappear.
• A California homeowner’s search for an $1,800 generator hit a roadblock because of state sales restrictions.
• A supposedly new generator from a warehouse retailer arrived with oil and a gas smell, raising return concerns.
Get TCD’s free newsletters for easy tips, smart advice, and a chance to earn $5,000 toward home upgrades. To see more stories like this one, change your Google preferences here.
© 2025 THE COOL DOWN COMPANY. All Rights Reserved. Do not sell or share my personal information. Reach us at hello@thecooldown.com.

source

Posted in Renewables | Leave a comment

Frontier breaks ground on Waroona solar and battery project – pv magazine Australia

Perth-based clean energy developer Frontier Energy announced major construction has commenced on Stage One of its flagship Waroona Renewable Energy Project in southwest Western Australia with first generation scheduled for 2028.
The first stage of the project, located about 120 kilometres south of state capital Perth, comprises a 132 MW solar facility and an 81.5 MW / 6.9-hour battery energy storage system. The DC-coupled system has been designed to capture solar energy during the day and dispatch electricity into the grid during periods of high-value demand.
Frontier Chief Executive Officer Adam Kiley said the project – that will connect to WA’s main electricity network, the South West Interconnected System (SWIS), via the nearby 330 kV Landwehr Terminal – will make a major contribution to the state’s clean energy transition, with the first stage of the project forecast to replace a third of the power generated by the coal-fired Collie power station that is due to close in 2027.
“When energy generation commences in 2028, our Waroona project will become the largest solar and battery hybrid facility connected to WA’s main electricity network and will be a major part in helping the state reach its target of 75% renewable energy by 2031,” he said, adding that the company’s intent is to develop Waroona into a multi-stage renewable energy hub.
“Stage One is only the beginning for Frontier, as we aim to expand beyond Stage One and establish the Waroona project as a major renewable energy hub in the heart of southwest WA, bringing much-needed new generation onto the grid in an area that has been supported by coal for more than 60 years,” he said.
Beyond Stage One, Frontier intends to expand the development significantly. Its longer-term ambition targets approximately 1 GW of solar generation and 660 MW of battery storage by 2031.
Stage Two already has development approval and proposes approximately 120 MW of solar generation alongside 80 MW of battery storage.
Western Australian contractor Monford Group holds the fixed-price engineering, procurement and construction (EPC) contract for the first stage of the Waroona project. Its responsibilities include constructing and commissioning the integrated solar and battery facility.
Chinese manufacturer Longi has been tapped to supply the solar modules, while Trina Storage will provide the battery system. Nextpower will supply solar tracking equipment, with SMA Australia providing inverters.
Major construction works include field piling for installation of the single access tracking system, followed by installation of the PV modules and construction of the solar facility balance of plant, which is scheduled to commence in early 2027.
The start of construction proper on the Waroona project comes after Frontier earlier this month executed a syndicated facility agreement for project finance debt facilities of up to $280 million (USD 194 million) provided by a syndicate of international lenders led by France-headquartered investment bank Natixis CIB and Japanese financial services conglomerate Sumitomo Mitsui Banking Corporation.
The company has also executed its Capacity Investment Scheme agreement with the Australian government which provides a minimum level of guaranteed revenue support for the project until 2042.
Frontier has also been assigned capacity credits for stage one of the Waroona project as part of the Australian Energy Market Operator’s Reserve Capacity Mechanism. The fixed five-year agreement ensures revenue certainty of circa $160 million for the project.
This content is protected by copyright and may not be reused. If you want to cooperate with us and would like to reuse some of our content, please contact: [email protected].
Comments
Please login to comment
The new issue of pv magazine Global is out now!
Available in print and digital – get your copy today!
Monday, November 23, 2026
11:00 am – 12:00 pm CEST, Berlin, Paris, Madrid

You have no items in your basket.

source

Posted in Renewables | Leave a comment

Breaking free of fossil fuels – The News Pakistan

The installed net-metered solar PV capacity in Pakistan increased exponentially from 0.7GW in June 2022 to 8.3GW in December 2025. Thus, over three years and six months, Pakistan’s installed net-metered solar PV capacity grew more than elevenfold.

SOLAR ENERGY
The installed net-metered solar PV capacity in Pakistan increased exponentially from 0.7GW in June 2022 to 8.3GW in December 2025. Thus, over three years and six months, Pakistan’s installed net-metered solar PV capacity grew more than elevenfold.
SolarPower Europe notes that grid electricity tariffs increased by 155 per cent between 2021 and 2024, while prices of Chinese PV modules fell sharply during the same period. Rising grid electricity tariffs and falling module prices created ideal economic conditions that triggered a solar PV boom in the country. Pakistan imported approximately 17GW of solar PV modules in 2024 and, according to estimates, cumulative solar PV module imports had exceeded 51GW by early 2026.
As a direct result of the increase in installed solar PV capacity, Pakistan avoided spending over $12 billion on oil and gas imports between 2021 and February 2026, according to estimates by the Centre for Research on Energy and Clean Air. Fossil fuel imports into the country decreased by 40 per cent between 2022 and 2024.
Energy think tank Ember applauds Pakistan’s consumer-driven distributed solar transition and estimates that approximately 38GW of distributed solar PV capacity had been deployed in the country by June 2025. It further notes that Pakistan installed 27GW of distributed solar in just two years, equivalent to the total installed capacity of all coal, gas, and oil power plants ever built in the country. Most importantly, distributed solar offers consumers electricity at almost half the price of conventional grid-based electricity. Ember highlights that residential distributed solar with a medium-sized battery generates electricity at approximately Rs20 per kWh, half the cost of grid electricity at Rs40 per kWh.
As for grid-based electricity generation, the Pakistan Economic Survey 2025-26 states that 46.2 per cent of electricity was generated from thermal sources in FY2025, followed by 31.5 per cent from hydropower, 17.7 per cent from nuclear power and 4.5 per cent from renewable sources. We should phase out our reliance on fossil fuels for grid electricity generation. Solar PV technology is already mature in Pakistan, and we must deploy it to its full potential to make our economy more resilient to global energy price hikes.
In terms of grid-installed capacity, Pakistan had 27.5GW of thermal capacity, followed by 11.5GW of hydropower, 3.5GW of nuclear power and 2.8GW of renewables in FY2025. The government should significantly increase grid-based installed solar PV capacity by 2030. This would be a much-needed step in the right direction, helping to curb emissions, reduce the energy import bill, ease pressure on Pakistan’s foreign exchange reserves, create jobs in the renewable energy sector and increase the country’s installed renewable energy capacity. Doing so would also make Pakistan’s economy more resilient to global energy price shocks.
Pakistan should aim to increase its grid-based installed solar PV capacity to 30GW by 2030. We must phase out fossil fuels from grid electricity generation and significantly increase our reliance on renewables, particularly solar PV technology. The World Bank notes that if Pakistan deployed solar PV across just 0.071 per cent of the country’s area, it could easily meet its current electricity demand. The country therefore has considerable solar PV potential, while the technology is already mature in Pakistan, as demonstrated by the installation of 27GW of distributed solar in just two years.
The government needs to completely phase out fossil fuels from grid electricity generation. In fact, it should legislate a commitment to phase out fossil fuels by 2035 and nuclear power by 2040, with the aim of generating 100 per cent of grid electricity from renewable sources by 2040. We have what it takes to make this happen.
The International Renewable Energy Agency (IRENA) highlights that China had a cumulative installed solar photovoltaic (PV) capacity of over 1,200GW in 2025, followed by the US with over 209GW, India with over 131GW, Germany with over 107GW, Japan with over 92GW, Brazil with over 64GW, Spain with close to 45GW, Australia with over 42GW, Italy with over 41GW and the Republic of Korea with over 34GW. These figures demonstrate the scale of solar PV deployment taking place globally and the potential for countries to expand their solar capacity.
As discussed earlier, Pakistan has considerable solar PV potential, while its decentralised installed solar PV capacity is already well established. Most importantly, residential solar with a medium-sized battery generates electricity at approximately Rs20 per kWh, half the cost of grid electricity at Rs40 per kWh. Distributed solar is therefore more cost-competitive than grid electricity. The combination of available potential, mature PV technology and price competitiveness makes solar PV one of the most suitable electricity generation technologies for Pakistan.
To conclude, we cannot afford to maintain the status quo in grid electricity generation in Pakistan, as it is hindering economic growth through expensive electricity tariffs and massive power cuts. It is pertinent to point out that high electricity tariffs increase production costs for manufacturers in Pakistan. Similarly, power cuts affect the quality of products manufactured in our factories and industries. The president of the Karachi Chamber of Commerce and Industry highlights that power cuts increase operational costs, disrupt production schedules and machinery-sensitive processes, delay deliveries and negatively affect export commitments. Higher production costs and lower product quality will consequently make Pakistani products less competitive in international markets. Goods produced in other countries using cheaper electricity and maintaining better quality will inevitably outcompete Pakistani products.
Consider the apparel sector. The Pakistan Business Council points out that Bangladesh has annual apparel exports worth over $49 billion. In contrast, Pakistan’s apparel exports are worth less than $9 billion. The Pakistan Business Council also notes that industrial electricity and gas tariffs in Pakistan are among the highest in the region. Other reasons for Pakistan’s low apparel exports include low labour productivity, outdated skills and minimal female participation in the sector.
Now is the time to set our priorities in order, accelerate sustainable development in Pakistan, boost export revenues, reduce our trade deficit and make our products more competitive in international markets. We need to phase out fossil fuels and nuclear power from Pakistan’s grid electricity generation. We can achieve this by 2040, with fossil fuels phased out by 2035, and we have what it takes to generate 100 per cent of our electricity from renewable sources.
Achieving this transition will also require investment in battery storage, transmission and distribution infrastructure and modernising the national grid to accommodate intermittent renewable energy sources.
By producing 100 per cent of our electricity from clean sources, we can reduce our energy import bill. The dollars saved could then be reinvested in Pakistan’s economy to address unemployment, foster green growth, reduce emissions, achieve the goals outlined in the Paris Climate Agreement and mitigate climate change.

The writer is a Stockholm-based policy analyst and the founder of Project Green Earth (www.projectge.org). He can be reached at [email protected].
Date:

source

Posted in Renewables | Leave a comment

Solar power plant opened in Côte d’Ivoire with expected output of nearly 90 GWh per year — France 24 – UA.NEWS

A new solar power plant was opened in July in the city of Ferkessédougou in northern Côte d’Ivoire. It is expected to generate nearly 90 gigawatt-hours of electricity annually.
The new facility and the country’s solar targets are covered in a France 24 video report published on November 15, 2026. Video author Julia Guggenheim visited the station in Ferkessédougou. The report is 2 minutes and 6 seconds long.
More current news is available on the UA.News Telegram channel Telegram.
Côte d’Ivoire is heavily dependent on fossil fuels. The report examines whether the country can transition to solar energy to make energy consumption more environmentally friendly and sustainable. France 24 describes the plant as new. The station is located in the north of the country. France 24 presents its opening in July in the context of seeking an alternative to fossil fuels.
Use of materials from the websites https://ua.news/ is permitted only if a reference (or, for online publications, a hyperlink) to UA.NEWS is included no later than the third paragraph.
Use of materials is permitted only upon receipt of written permission from the UA.NEWS editorial board and the mandatory placement of a direct hyperlink to the original publication https://ua.news/ in the first paragraph of the material, which must be open to indexing by search engines.
Materials marked with the “Advertisement” label are promotional and are published as advertisements. The editorial board may not share the views promoted therein. The editorial staff is not responsible for the facts and opinions published in advertising materials. In accordance with current Ukrainian legislation, the advertiser is responsible for the content of the advertisement.
Materials in the “Blogs” section represent the personal opinion of the blog author; the editorial staff may not share the author’s views.
Copyright infringement is prosecuted in accordance with the current legislation of Ukraine and the norms of international law.
The online media outlet UA.NEWS serves only an audience aged 21 and older. Online media entity; media identifier – R40-05225.
LLC “NEWS FLASH INFORMATION AGENCY.” All rights reserved.

source

Posted in Renewables | Leave a comment

rPlus Energies secures $450 million to fuel Western U.S. solar expansion – Energies Media

Energies Media
The United States government deserves huge credit for the way it has fostered an environment where energy companies are encouraged to pursue clean energy projects despite the profit and short-term benefits that come with fossil fuel-based projects. The government is working collaboratively with private companies with the understanding that if it reduces the amount of restrictions and approves projects, the country will be able to reduce carbon emissions and reach its clean energy targets with ease. The latest company to be involved in a captivating initiative is rPlus Energies after it secured $450 million to fuel Western U.S. solar expansion.
Now more than ever before, there is a need for companies to invest millions of dollars if they want to build facilities or execute projects that match the modern-day standard. Technology and science have heavily impacted the energy sector to the point where developers are aiming to predict where the energy sector is headed and position themselves to benefit when that time comes.
rPlus Energies is a U.S. renewable energy developer focused on large-scale solar, wind, and pumped storage hydro projects. The company is headquartered in Salt Lake City, Utah, and was established in 2018, which is fairly new considering that there are solar entities that have existed for multiple decades. Because it was recently established, the company was not forced to adapt, as it was already utilizing contemporary strategies.
According to reports, rPlus Energies operates as a subsidiary of the Gardner Group and is backed by Sandbrook Capital. The company’s CEO is Luigi Resto. One of the advantages that the company has over its competitors is that it is capable of executing a wide range of clean energy projects, which is something that not all companies can do.
A press release from rPlus Energies revealed that the company has closed a revolving credit facility of up to $450 million to support the continued development and construction of its near-term pipeline of solar and energy storage projects across the American West. One of the most important targets for the United States is to diversify its energy portfolio and ensure that there is consistent energy generation everywhere.
As such, rPlus Energies’ decision to focus on Western America is important for the nation’s overall targets. The facility provides both funded borrowing capacity and letters of credit. It is also supported by cash flows from almost 1 GW of operating assets, including the Green River Energy Center and Pleasant Valley Solar 2, which reached commercial operation and completed term financing earlier in the year.    
California anchors the Western U.S. solar landscape with over 56.5 GWdc of installed solar capacity, while the Bureau of Land Management is actively expanding public-land solar planning across 11 Western states to support a net zero grid by 2035. California generates almost 10,000 megawatt-hours monthly, producing roughly 20.3% of the U.S. total and leads the nation in small-scale/rooftop solar systems.
For rPlus Energies, the company must remain committed to establishing its presence in the West. Securing the facility is an essential step as the company continues to scale the business. It reflects the progress that the company’s team has made and the confidence its lenders have in its long-term vision. Kirkland & Ellis served as legal counsel to rPlus Energies, whereas Milkbank served as legal counsel to the lenders.
Canadian Imperial Bank of Commerce, New York Branch served as Lead Arranger and Administrative Agent for the three-year facility, which was syndicated to a group of leading financial institutions including National Bank of Canada, Truist Bank, KeyBank, Wells Fargo, MUFG and Zions Capital Markets. The initiative is a reflection of how involved the U.S. government is in the projects that are materializing.
Prince is a versatile writer focused on energy, automotive, environmental, and general news topics. He makes complex technical and policy issues clear, engaging, and accessible for a broad audience.
Prince is a versatile writer focused on energy, automotive, environmental, and general news topics. He makes complex technical and policy issues clear, engaging, and accessible for a broad audience.
Prince is a versatile writer focused on energy, automotive, environmental, and general news topics. He makes complex technical and policy issues clear, engaging, and accessible for a broad audience.

source

Posted in Renewables | Leave a comment

How One 13-Year-Old Is Helping Solve A Huge Solar Panel Limitation – Engadget

Tired of moving solar-powered Christmas lights, a seventh grader built a tracker that lets gravity do the work.
Jason Chang was sick of his mother asking him to adjust the family’s solar-powered Christmas lights to get more sun, so he devised a solution with big potential. The 13-year-old seventh grader at Worcester Academy in Massachusetts created a solar tracker that utilizes water and gravity to move a solar panel without the need for a motor, a sunlight sensor or electricity to power the mechanism.
The prototype was less than $25 and generated about 20 percent more voltage than a stationary panel in outdoor tests, CBS Boston reports. The contraption tackles a basic limitation of fixed solar panels: the inability to change position as the sun moves across the sky. This teenager’s bright idea is attracting national attention. Here’s how it works. 
Chang’s invention is similar to a seesaw. A small solar panel is mounted on a rotating wooden structure, with water dripping into a bucket on one side. The frame tilts the panel throughout the day as the bucket fills, increasing its weight. There’s no sensor needed to determine the sun’s position, and the drip rate is adjusted to keep the panel tilting at approximately the correct speed.
It’s not difficult to get the process started. Simply pull the plug to set the water in motion. However, it took a lot more work to get that flow just right. Chang spent over a year refining the project, jotting down his tests in a notebook and using recycled materials for much of the construction. And while gravity is free of cost, trying to make it work on a schedule takes a little engineering.
The reported 20 percent improvement also needs to be examined. In the outdoor comparisons, Chang’s setup was able to generate higher voltage, but that doesn’t necessarily translate to a 20 percent increase in power or total energy output. To calculate those gains, current readings and energy measurements over time would be required, but were not included in the report. It’s a positive outcome for a student prototype, but not a guarantee to save you 20 percent on your electric bill.
Using water and gravity to follow the sun isn’t entirely new. There are commercial trackers on the market that can move with the sun, but they cost more than fixed units. There are also some build-it-yourself designs similar to Chang’s concept. Engineering for Change promotes a SunSaluter rotating solar panel kit with a suggested retail price of $50. That cost doesn’t include the panel, battery, and other components. Chang’s version offers another inexpensive DIY take on the idea, rather than a commercially ready replacement for existing trackers.
There’s a practical reason why most rooftop solar panels aren’t designed to move around. Trackers can boost energy yields from ground-mounted arrays, but they also add costs and maintenance. It’s easy to tilt a small wooden frame, but mounting moving panels on a roof where they have to withstand wind and rain is where it gets complicated. Any extra electricity would have to be worth the investment and maintenance. Another fixed panel might be a lot less hassle for some homeowners.
Sure, motor-free tracking could still appeal to people running small off-grid systems, where every bit of power counts. However, water has its own set of issues. While cold weather can actually boost solar panel efficiency, a mechanism that relies on flowing water has an unwelcome winter issue: ice, which is why Chang is working on a winter version.
CBS did not say how often the water needs to be refilled, how often the tracker needs to be reset, or whether the design has been tested with full-size panels in strong winds. Regardless, Chang’s work as a seventh-grader is exceptional. In 2026, he was one of 55 students recognized as National STEM Champions.

source

Posted in Renewables | Leave a comment

Fire reported at Twiggs County solar farm, fire department says it is now contained – 13WMAZ

Fire reported at Twiggs County solar farm, fire department says it is now contained  13WMAZ
source

Posted in Renewables | Leave a comment

Solar Panel Recycling in Gujarat Faces a 2030 Capacity Test – Urban Acres

Gujarat’s solar expansion is creating an infrastructure problem that the state’s power plans cannot solve through generation capacity alone. The state is projected to produce 11,528 tonnes of solar photovoltaic waste by 2030, while its recycling ecosystem still lacks dedicated collection networks, commercial-scale processing capacity, digital traceability and clear financial incentives, according to a July 2026 report by the Gujarat Rajya Institution for Transformation (GRIT) cited by the Times of India.
The issue is not limited to panels reaching the end of their expected 25-to-30-year operating life. Manufacturing scrap, defective modules, breakage during transportation and installation, faulty installation and damage caused by storms, floods and hailstorms are already contributing to the waste stream. That changes the planning question. Solar waste is not a distant disposal problem that will begin only when the first large generation of projects is retired; it is an industrial and municipal management issue that grows alongside capacity additions.
Gujarat had 25.5 GW of installed solar capacity as of December 2025, making it one of India’s largest solar markets. The figure reflects the scale of the state’s energy transition, but it also indicates why end-of-life management cannot remain an informal or fragmented activity. Solar installations are spread across utility-scale sites, industrial premises and rooftop systems. The waste generated by these locations will differ in volume, timing and accessibility, requiring a system that can track panels from installation through reuse, repowering, recycling or disposal.
The GRIT report identifies gaps at several points in that chain. Stakeholder consultations cited in the report point to limited collection infrastructure, a shortage of commercial-scale recycling technology, weak digital traceability and inadequate financial incentives. The report also notes the absence of dedicated collection centres and the dependence on informal scrap dealers for panels coming from dispersed rooftop installations. These weaknesses could make it difficult to identify where panels are located, determine whether they can be reused and ensure that damaged modules reach facilities capable of recovering their materials.
The material value of discarded panels is one reason the emerging waste stream is also being viewed as an industrial opportunity. Solar modules contain silicon, silver, copper, aluminium and glass that can potentially be recovered and reintroduced into manufacturing. Solar energy consultant Jaideep Malaviya told the Times of India that recovery could create a secondary raw material market, support domestic manufacturing and reduce dependence on virgin resources. That opportunity, however, depends on the economics and logistics of dismantling and processing panels at scale.
India’s projected growth makes the question larger than Gujarat. The GRIT report estimates cumulative solar waste at around 100 kilotonnes in financial year 2023, rising to 340 kilotonnes by 2030 and approximately 19,000 kilotonnes by 2050. About 67% of the projected waste by 2030 is expected to be concentrated in five states: Gujarat, Rajasthan, Karnataka, Tamil Nadu and Andhra Pradesh. The concentration of waste in a small group of major solar states creates a potential basis for specialised recycling clusters, but it also means that capacity and standards in these states will shape how India manages the material consequences of solar growth.
The state’s existing solar fleet is beginning to create a replacement cycle. Gujarat was among India’s early adopters of solar power, and some large installations are now approaching two decades of operation. At the same time, newer modules offer higher output and improved performance within the same land footprint. Developers and operators are therefore increasingly considering repowering existing projects by replacing older panels. Repowering can improve electricity generation from established sites, but it also creates a concentrated flow of used modules that need to be assessed, moved, dismantled and either reused or recycled.
Reuse is emerging before recycling reaches full commercial scale. Solar companies in South Gujarat are shifting older panels from sites with high electricity requirements to locations where demand is lower and land is more available. Rakesh Trivedi, director of Solar Smart Power Pvt Ltd, said used panels can be installed at client sites with lower power demand, while damaged panels currently generated are taken back by manufacturers for recycling at their plants. This model extends the operating life of panels and delays disposal, but it requires reliable information about module condition, performance and ownership.
Reuse also cannot absorb every panel entering the waste stream. Modules damaged by extreme weather, transportation or installation may not be suitable for redeployment. Panels with severe degradation may produce too little power for their original location, even if they remain useful elsewhere. The distinction between a reusable panel, a repairable component and a material for recycling therefore becomes important for both environmental management and commercial viability. A collection system that treats all discarded panels as ordinary scrap could lose recoverable value and increase the risk of unsafe or inefficient processing.
Weather-related damage adds another layer of uncertainty to the timing and geography of waste. Gujarat’s solar installations are distributed across districts and exposed to storms, flooding and high-wind events. The source report identifies these events as contributors to premature module failure. That means waste volumes will not be determined only by installation age. They will also reflect asset location, mounting quality, maintenance practices and the severity of local weather events. The available material does not establish a district-wise forecast, but it shows why a purely age-based recycling plan would be incomplete.
The institutional responsibilities are also still taking shape. Tejas Patel, former president of the South Gujarat Solar Association, said there were no clear guidelines or policies for handling solar power plant waste at present. He also said the Surat Municipal Corporation had announced incentives for waste recycling, including solar waste, while noting that one recycling plant was operating in Chennai. Surat’s offer of leased land is an attempt to address the physical and investment barriers facing the sector, but land alone cannot create a recycling ecosystem. Collection arrangements, technology, compliance requirements, feedstock certainty and long-term commercial incentives will determine whether facilities can operate continuously.
One proposed project illustrates the scale of private investment being considered. Kalpesh Kalathia, chairman of Kosol Energie, said the company plans to establish a solar panel recycling facility in Kachchh in partnership with a European company. The proposed unit would involve an investment of about Rs 40 crore and have a stated capacity of around 6,000 panels per day. The project remains a company plan as described in the report; the supplied material does not provide an operational date, final approvals or details of the technology to be used.
The proposed Mega Eco-Industrial Park at Botad, identified under the North Gujarat Economic Master Plan, is another possible institutional location for integrating solar PV recycling, resource recovery and circular manufacturing. Such an industrial approach could link waste processing with the production of secondary materials, but the source material does not establish whether solar recycling has been formally incorporated into the park’s implementation plan. That distinction matters because identifying a potential site is different from creating a functioning supply chain.
The central policy challenge is coordination. Solar developers, manufacturers, EPC companies, municipal bodies, scrap dealers, recyclers and state agencies each encounter different parts of the waste stream. Without traceability, panels removed from a rooftop installation may enter informal channels with little documentation. Without collection points, even responsible owners may find it difficult to move small quantities economically. Without predictable volumes, recycling companies may hesitate to invest in machinery. And without clear incentives or rules, reuse, recovery and safe disposal may compete on uneven terms.
The numbers show why these issues require attention before Gujarat reaches the projected 11,528 tonnes of waste in 2030. India’s solar waste is expected to rise from around 100 kilotonnes in financial year 2023 to 340 kilotonnes by 2030, while the long-term projection reaches approximately 19,000 kilotonnes by 2050. These figures are projections cited in the GRIT report, not records of waste already processed. Their significance lies in the short window available to establish collection and processing systems before waste volumes become substantially larger.
Gujarat’s solar story is therefore entering a second infrastructure phase. The first phase focused on land, generation capacity, transmission and project deployment. The next must account for what happens when panels are damaged, replaced, reused or retired. The evidence supplied in the report confirms the scale of the projected waste stream and identifies the principal capacity gaps, while questions about final policy design, facility approvals, processing standards and implementation timelines remain open. The state’s next milestones will be the development of dedicated collection systems, clearer operating guidelines and the conversion of proposed recycling investments into functioning capacity.

Welcome to Urban Acres, a leading think tank dedicated to promoting sustainable urban built environments in the face of climate change and the need for zero net carbon solutions.
© 2022 Urban Acres | All Rights Reserved

source

Posted in Renewables | Leave a comment

Hyundai's Staria Gets Camper Conversion with Electric Pop-Up Roof and 520W Solar Panel – BigGo Finance

South Korean automaker Hyundai has unveiled the Staria Camper Concept, a vehicle based on its large Staria minivan and fitted with equipment for overnight stays in the car. It was announced to coincide with CMT 2026, a camping and travel trade fair held in Stuttgart, Germany, from January 16, 2026, and its hallmarks are features designed for “off-grid” use that does not rely on external power, such as an electrically operated roof and solar panels. Production has not been decided at this point, and the company says it will explore the possibility of mass production based on visitor feedback.
The base Staria is a multipurpose vehicle (MPV) that Hyundai launched in 2021. It was the first model to adopt an “inside-out” approach, in which the interior is designed first and then extended to the exterior, and it was initially offered with diesel and gasoline engines. The battery-electric Staria Electric made its world premiere at the Brussels Motor Show in January 2026. The Camper Concept builds on this BEV version and aims to present to the European market the potential of a camper that can handle both everyday transport and outdoor use.
Dimensions for the concept car have not been disclosed, but the base Staria Electric measures 5,255 mm long, 1,995 mm wide and 1,990 mm tall, with a wheelbase of 3,275 mm. Compared with Nissan’s new Elgrand (4,995 mm long, 1,895 mm wide, 1,975 mm tall, 3,000 mm wheelbase), which went on sale in July 2026, it is 260 mm longer and 100 mm wider.
Note: Dimensions of the Staria Camper Concept itself have not been disclosed. Figures are based on the production version of the base vehicle.
Its biggest feature is an electric pop-up roof that, when parked, raises the roof at the push of a switch to expand headroom. This improves usability when standing up or using the kitchen inside, while the roof closes during driving to reduce aerodynamic drag and wind noise. A 520W solar panel on the roof generates up to 2.6 kWh under average sunlight of five hours per day. It is intended to power in-car electrical devices and extend driving range.
Inside, there is a 36-liter refrigerator and a portable shower. The front seats are electrically operated individual seats that swivel 180 degrees, turning to face rearward to create a lounge-like space for face-to-face relaxation. The rear seats can be folded flat with the push of a button and used as a bed that sleeps two adults. The result is a dual-purpose vehicle: a minivan on the move and a living space when parked. Hyundai is also considering “smart glass” for the rear windows that can be electronically controlled for transparency and light blocking, operated from a dedicated touchscreen. In addition to ensuring privacy, it is expected to improve thermal insulation and soundproofing.
If it goes into production, the BEV Staria Electric would serve as the foundation. The European version is a front-wheel-drive model combining an 84kWh lithium-ion battery with a motor producing a maximum output of 160kW (218PS) and maximum torque of 350Nm, with a WLTP single-charge range of up to roughly 400 km (estimated). It adopts an 800V high-voltage system and, under optimal conditions, can charge from 10% to 80% battery capacity in about 20 minutes on DC fast charging. It also features a V2L function that can power electrical appliances inside and outside the vehicle. However, the range in camper configuration has not been disclosed.
Hyundai has also announced plans to bring the Staria to the Japanese market. Hyundai Mobility Japan has announced a “this winter” launch on a teaser page on its official website, and plans to introduce three types: a seven-seat “Lounge,” a nine-seat “Wagon” and a three-seat commercial “Van” model. The Japan-spec version is said to adopt a fast-charging system compatible with both 400V and 800V, but pricing, launch date, output and range have not been announced.
In the camper market, manufacturers are exploring the introduction of BEV-based models for overnight stays. Hyundai’s decision to bring the Camper Concept to a European trade fair is seen as an effort to capture demand for electric vehicles for outdoor use in Europe, where charging infrastructure is well developed. Power generation from solar panels and power supply from large-capacity batteries are factors that affect how long campers can stay at campsites with limited power facilities, and the focus will be on whether these can be pitched as features that compensate for short driving range.
In the Japanese market, the Staria’s entry itself represents a new market entrant, and attention is focused on the fact that it offers a wide range of derivatives, from a commercial van to a seven-seat lounge. If the camper concept is mass-produced, it could capture domestic outdoor demand as a product spanning both the minivan and camper markets. However, at this stage the company is still gauging reaction at the trade fair, and the timing and pricing of a commercial launch remain unclear.
Once added, BigGo Finance appears first in Google Search Top Stories, so you get the broadest, most up-to-the-minute, and most comprehensive global financial news first.
The news and data on this website are for reference only and do not constitute investment advice or an offer to buy or sell. Information is sourced from exchanges and public sources, and may be delayed, interrupted, or updated. While we strive for accuracy, we do not guarantee timeliness, correctness, or completeness. Content may include external links for which we are not responsible. By using this site, you agree that we and our partners are not liable for any losses. Investment carries full responsibility; please carefully assess risks and consult professionals. If there are errors in the content, please contact us for correction.

source

Posted in Renewables | Leave a comment

Longi achieves 35.31% efficiency in perovskite-silicon tandem solar cell based on self-assembled molecules – pv magazine Australia

Chinese solar module manufacturer Longi has developed a perovskite-silicon tandem solar cell using specially designed molecules that suppress excessive molecular stacking while maintaining efficient charge transport.
“This molecular design promotes the formation of a uniform, well-organized self-assembled monolayer (SAM), even on rough, pyramid-textured surfaces,” Longi researcher Bo He told pv magazine. “By balancing molecular packing and surface coverage, the engineered interface improves energy-level alignment for faster charge extraction, reduces defects through molecular flexibility, and provides a stable foundation for the growth of high-quality perovskite films.”
The researchers explained that conventional SAM molecules often suffer from excessive aggregation, resulting in uneven coverage on textured silicon surfaces. To address this limitation, they designed molecules with controlled molecular twisting and conjugation. They developed four SAM derivatives – TC0, TC1, TC2 and TC3 – based on the commonly used 4PACz molecule.
TC2 offered the best balance between molecular packing, substrate adhesion and charge transport, as its structure combines a conjugated backbone with a moderately twisted phenyl side group. Molecular simulations showed surface coverage of 83.1%, compared with 75.0% for TC1 and 73.3% for TC3. Experimental measurements confirmed that TC2 achieved more than 80% coverage and exhibited strong anchoring stability.
The improved molecular arrangement also enhanced the electronic properties of the interface between the indium tin oxide (ITO) layer and the perovskite absorber. In particular, TC2 modified the ITO work function and provided favorable energy-level alignment for efficient hole extraction. This strengthened the internal electric field, accelerating charge separation and transport, while improved interface coverage reduced defects and suppressed charge recombination.
The analysis also showed that TC2 promoted slower, more controlled perovskite crystallisation, producing larger, more uniform grains with higher crystallinity. The resulting films exhibited improved phase uniformity and reduced nonradiative recombination. Photoluminescence measurements showed a quantum yield of 1.46% and a quasi-Fermi level splitting of 1.292 eV, the highest values among the tested SAMs.
Using this molecular engineering approach, the researchers fabricated a two-terminal monolithic tandem solar cell combining a perovskite top cell with a heterojunction (HJT) bottom cell.
The device features a textured silicon bottom cell coated with an ITO recombination layer, followed by a TC2-based SAM serving as the hole-selective contact. The perovskite absorber is deposited on the SAM and covered with a lithium fluoride (LiF) interlayer, a fullerene (C60) electron transport layer and a tin oxide (SnOx) buffer layer. The stack is completed with a transparent indium zinc oxide (IZO) electrode, a silver (Ag) contact and a magnesium fluoride (MgFx) optical coating.
Under standard test conditions, TC2-based devices achieved an average open-circuit voltage of 2.007 V and a fill factor of 84.30%, outperforming cells based on 4PACz, TC1 and TC3. The champion device reached a power conversion efficiency of 35.31%, with a short-circuit current density of 20.82 mA/cm2, an open-circuit voltage of 2.007 V and a fill factor of 84.53%.
Independent testing by China’s National Center of Inspection on Solar Photovoltaic Products Quality (CPVT) certified a reverse-scan efficiency of 35.25%, a fill factor of 84.98% and a stabilized efficiency of 35.13%. External quantum efficiency measurements confirmed effective light absorption and current generation in both subcells.
Stability tests also demonstrated improved resistance to light-induced degradation and phase segregation in TC2-based perovskite films. The tandem devices retained 94% of their initial efficiency after 1,500 hours of continuous operation under the ISOS-L-1 protocol and 82% after 1,000 hours at 65 C under the ISOS-L-2 protocol.
“Overall, the results demonstrate that optimized molecular interface engineering can simultaneously improve the efficiency, charge transport and operational stability of perovskite-silicon tandem solar cells,” He said.
The cell technology is described in “Conjugation-regulated self-assembled molecules for tandem solar cells,” published in Nature. Researchers from China’s Soochow University, Northwestern Polytechnical University and Hong Kong Polytechnic University participated in the study.
The new development builds on a series of advances in molecular interface engineering for perovskite photovoltaics. In September, an international research team involving Hong Kong Polytechnic University and Northwestern Polytechnical University developed a symmetry-breaking molecular strategy that improved SAM coverage by combining symmetric and asymmetric molecules. The resulting inverted perovskite solar cell achieved an efficiency of 26.32%, with a certified value of 25.67%, while retaining 93% of its initial performance after 1,150 hours of operation.
In December 2025, researchers led by Northwestern Polytechnical University developed a perovskite-silicon tandem cell with a certified efficiency of 31.71%. Their approach relied on chemical polishing to selectively remove residual lead iodide from the perovskite absorber, reducing recombination losses and improving film uniformity. Around the same time, a team led by Soochow University achieved 32.3% efficiency using a steric-complementary interface design combining small, flexible molecules for defect passivation with larger molecules providing protection against environmental degradation. The device achieved a certified efficiency of 32.12%.
More recently, Longi and Soochow University developed a 34.0%-efficient tandem cell using a dual-anchored interface incorporating zirconium oxide (ZrO2) nanoparticles between the transparent conductive oxide and the SAM. The approach reduced interfacial recombination and leakage while maintaining efficient charge extraction. The device achieved an open-circuit voltage of 1.997 V and retained 84% of its initial efficiency after 2,000 hours of operation.
Longi has also continued to advance tandem cell efficiency. In April 2025, the manufacturer achieved a certified efficiency of 34.85% for a two-terminal perovskite-silicon device, using a bilayer passivation strategy based on lithium fluoride and ethylenediammonium diiodide. In July 2026, the company raised its tandem cell efficiency record to 35.5%, with the result independently certified by the European Solar Test Installation (ESTI).
Alongside its tandem research, Longi has made progress in conventional crystalline silicon technology. In November 2025, the company disclosed the technical details of its 27.81%-efficient silicon solar cell, based on a hybrid interdigitated back-contact architecture combining passivated tunneling contacts, dielectric passivation layers and optimized carrier transport.
From pv magazine Global
This content is protected by copyright and may not be reused. If you want to cooperate with us and would like to reuse some of our content, please contact: [email protected].
Comments
Please login to comment
The new issue of pv magazine Global is out now!
Available in print and digital – get your copy today!
Monday, November 23, 2026
11:00 am – 12:00 pm CEST, Berlin, Paris, Madrid

You have no items in your basket.

source

Posted in Renewables | Leave a comment

CER Inspection Report: Solar and Battery Installation Faults – Energy Matters

CER Inspection Report: Solar and Battery Installation Faults  Energy Matters
source

Posted in Renewables | Leave a comment

China solar panel prices slip as year-end shipping push brings concessions – Green Building Africa

Module prices in China continued to decline this week, according to the latest weekly spot price update from InfoLink Consulting, covering transactions from November 5 to November 11, 2026. Most manufacturers are racing to meet shipment targets set at the start of the year, and prices are gradually softening as suppliers offer concessions to move volumes before the year closes.
BC module quotes for distributed projects dropped by RMB 0.01/W, a fall of about 1.2%, to RMB 0.80/W. The overall BC average declined by RMB 0.005/W, or about 0.6%, to RMB 0.787/W. Actual delivery prices for BC modules currently sit at RMB 0.75 to RMB 0.77/W for ground mounted projects and RMB 0.78 to RMB 0.81/W for distributed projects.
TOPCon modules remain cheaper. Delivery prices in China are around RMB 0.65 to RMB 0.71/W for ground mounted projects and RMB 0.68 to RMB 0.76/W for distributed projects. Outside China, the average TOPCon module price has stayed at US$0.114/W.
The softer module market follows weakness further up the supply chain. Wafer prices fell more sharply this week across all three mainstream formats, and cell quotes moved lower as upstream costs eased. Polysilicon prices were stable at RMB 42 to RMB 43/kg for n type recycled material, but falling futures, slow destocking and weak downstream demand have left buyers and sellers far apart on price. Manufacturers are holding an estimated 380,000 to 390,000 MT of polysilicon inventory, even as output is set to fall to about 82,000 MT in November. With the year end installation rush in China expected to finish in early December, cell quotes may struggle to climb back to RMB 0.32/W, which could keep pressure on module pricing.
Conditions differ across export markets. In the Middle East, regional conflict continues to disrupt shipments and cause logistics delays for most projects, and deliveries remain constrained for now. In Europe, module prices held steady this week.
In the U.S., the August 6 Section 232 announcement is expected to significantly affect module price trends. With the minimum import price acting as a price floor, both imported and domestically manufactured modules are expected to become more expensive once the measures take effect. In India, prices for a small number of recent orders have moved higher, mainly because buyers are stocking up early ahead of the impact of the U.S. measures. Increases have been more pronounced for projects not subject to the Domestic Content Requirement, while changes for projects covered by the requirement have been relatively limited, as demand there is driven mainly by the domestic market.
For African developers and procurement teams, the current weakness in Chinese module prices may offer room to negotiate, although rising U.S. and Indian prices and ongoing Middle East logistics delays are factors to watch when planning delivery schedules.
Author: Bryan Groenendaal






October 7, 2026
October 12, 2026
November 14, 2026
October 18, 2026
October 30, 2026
November 4, 2026
Disclaimer | Privacy Policy | Terms & Conditions | Returns Policy | Intellectual Property | Cookie Policy
© 2019 – 2026 GBA Digital Media Group. All Rights Reserved
Website Design | Website Maintenance

Subscribe to our weekly Top 5 Stories
"*" indicates required fields

source

Posted in Renewables | Leave a comment

MA-Free Perovskite Solar Module Hits 22.70% Efficiency – News and Statistics – IndexBox

We use cookies to improve your experience and for marketing. Read our cookie policy Manage cookies
Search across reports, market insights, and blog stories.
A team of researchers from the Chinese Academy of Sciences and Dalian Jiaotong University has fabricated a small solar module using a perovskite material that contains no methylammonium molecules, according to pv magazine. The work, published in Advanced Materials, addresses the intrinsic thermal and chemical instability of methylammonium, which at elevated temperatures can drive decomposition of perovskites such as MAPbI3, release volatile species, promote formation of lead iodide, raise defect density and reduce charge-carrier performance and efficiency.
The researchers used slot-die coating under ambient conditions to produce uniform, high-efficiency methylammonium-free modules. Corresponding author Zhihua Zhang described the fabrication process as reliable and noted that slot-die coating is attractive for large-scale manufacturing because it combines efficient material use with integration into continuous roll-to-roll production. Unlike spin coating, the technique allows controlled deposition of precursor inks over large substrates, though achieving homogeneous coverage and controlled crystallization remains difficult when scaling from laboratory devices to large-area modules.
To manage crystallization, the team applied a combined additive strategy based on rubidium thiocyanate and formamidinium thiocyanate. The two additives work through an in situ coordination mechanism that helps convert the non-photoactive delta phase into the photoactive alpha phase while limiting unwanted secondary phases. Zhang said the approach makes the crystallization process itself more tolerant of processing variability rather than imposing tighter process constraints, lowering the energy barrier for the phase transition and broadening the processing window between deposition and annealing.
The combined additives extended the processing window for uniform crystallization to more than 100 seconds, enabling dense films with large crystal grains, a uniform vertical compositional gradient and lower residual stress. Small-area solar cells reached a power conversion efficiency of 26.16%, while a larger module with an active area of 54.80 cm2 reached 22.70%, compared with 15.8% for a reference module made without the additive strategy.
Operational stability also improved. Unencapsulated devices retained 97.76% of their initial efficiency after 1,300 hours of continuous operation at the maximum power point under AM 1.5G illumination at 65 C, while reference devices retained 65.86% under the same conditions. The findings were presented in the paper Processing Window Expansion Enables Uniform Crystallization in Scalable Ambient-Fabricated Perovskite Photovoltaics.
This report provides an in-depth analysis of the Perovskite Solar Cells market in China, including market size, structure, key trends, and forecast. The study highlights demand drivers, supply constraints, and the competitive landscape across the value chain.
Tell us where to send the sample and whether you want this report customized.
Thank you. Our team will review your request and reply to your business email.
Our team will review your request and route it to support@indexbox.io.
IndexBox, Inc.
2093 Philadelphia Pike #1441
Claymont, DE 19703, USA
Contact us
© 2026 IndexBox, Inc
Instant access. No credit card needed.
Online access to 2M+ reports, dashboards, and tables. Trusted by Fortune 500 teams.
Free Data: Solar Cells and Light-Emitting Diodes — China
Instant access. No credit card needed.

source

Posted in Renewables | Leave a comment

T1 Energy Reports Third-Quarter Results, Expands Solar Module Contracts – TipRanks

T1 Energy Reports Third-Quarter Results, Expands Solar Module Contracts  TipRanks
source

Posted in Renewables | Leave a comment

Fire reported at Twiggs County solar farm along Highway 129 – WGXA

Now
45°
Mon
62°
Tue
66°
by Gloria Ruth Finney
Emergency crews responded to a reported fire at a solar farm along Highway 129 in Twiggs County Sunday.
A Twiggs County resident contacted WGXA after hearing reports of a possible fire at the solar facility. The resident said a relative captured a photo of the incident and that others reported seeing smoke from as far away as Bonaire.
WGXA attempted to contact Twiggs County Fire-Rescue, but was unable to reach anyone, as the department operates on a volunteer responder basis and is closed on weekends.
Around 5:15 p.m. Sunday, WGXA spoke with a dispatcher at the Twiggs County Sheriff’s Office using its non-emergency number.
The dispatcher confirmed a fire at the solar panel farm along Highway 129 and said emergency crews were on scene.
The dispatcher said additional information would be available Monday, when emergency management services for the area reopen.
WGXA will continue working to learn more about the fire, including its cause, whether there were any injuries and the extent of any damage.
2026 Sinclair, Inc.

source

Posted in Renewables | Leave a comment

Germany’s solar power production nears record level – CediRates

source

Posted in Renewables | Leave a comment

Portugal’s Alto Rabagão floating solar farm becomes a storm test site for self-adjusting mooring buoys and 3D-printed concrete anchors – Energies Media

Energies Media
When it comes to technology, the weather does not care how clever it is. 
While the water may be calm one minute, this can change suddenly to being windy with big waves – something that carefully engineered structures have to be able to withstand. 
With renewable energy efforts becoming increasingly ambitious, people have to consider: what do you do when nature refuses to play nice?
EDP is putting this to the test at Portugal’s Alto Rabagão reservoir, where it has opened the Floating PV Lab.
There, developers can use an operating hydropower and solar environment to see how equipment behaves when exposed to the elements.
The location was not chosen at random. 
2016 marked the start of EDP’s floating photovoltaic pilot at Alto Rabagão, where it pioneered a model allowing solar and hydropower to share infrastructure. 
The setting of this particular reservoir is a demanding one, as it sees strong winds, waves, snow, ice and fluxtuations in temperature. 
In other words, this is not so much a gentle product demonstration than it is an energy-tech obstacle course.
Yes, the setting is harsh. But that is precisely the point. 
As reservoir levels change, floating solar platforms need to remain stable, with anchors and moorings coping with the wind and waves. 
This is why real-world testing is so important, as it can help to expose weaknesses, refine designs and reduce risks. 
That opportunity to learn is now available beyond just one company with EDP’s lab, which allows businesses and research partners to find solutions that could help to make these innovations suitable for commercial use. 
How, exactly, do you keep a floating solar farm from becoming a floating-away solar farm?
Currently, two solutions are being explored by EDP at Alto Rabagão: one to address the challenges of mooring, and the other anchoring. 
One of these experimental projects is a buoy that is able to adjust to changing water levels, with the second one giving traditional concrete anchors a modern makeover. 
An automatic tension buoy for floating photovoltaic systems is being tested by Norwegian company, Fred. Olsen 1848.
The objective with this buoy is that it will be able to maintain the right amount of tension in the mooring arrangement.
The varying levels at Alto Rabagão make this the perfect place to put new technologies to the test, revealing how systems must adapt.
Gravity anchors made with 3D-printed concrete are also being trialled by California-based company, Sperra. 
Their geometry is able to be customised to fit site-specific loads, mooring configurations and ground conditions. 
The benefits of this are that it could improve performance and reduce the cost and complexity, making installation more efficient. 
Both of these pilots will be running for a year and, if any of these concepts are validated, the solutions could end up featuring in floating-solar installations in the future. 
With a goal of supporting the commercialisation of at least five new technologies by the end of 2027, EDP will be operating the lab for three more years. 
When considering the future of floating solar, it’s about more than just shiny panels and bright ideas. 
It’s also about the engineering that keeps them secure and functioning when the weather gets rough. 
With EDP opening Alto Rabagão to shared experimentation, difficult conditions are being turned into useful data in a collaborative setting. 
One of the other challenges facing renewable energy is having electricity available when it’s needed. But could the new generation of power storage be the answer?

source

Posted in Renewables | Leave a comment

Homeowner eyeing solar in Greece seeks answers on where power goes if often not home during day – The Cool Down

© 2025 THE COOL DOWN COMPANY. All Rights Reserved. Do not sell or share my personal information. Reach us at hello@thecooldown.com.
Commenters jumped in to help with information and suggestions.
Photo Credit: iStock
Low electricity demand and a daytime schedule away from home complicated one Greek homeowner’s hopes of using their sunny apartment to cut power bills.
The homeowner asked an online community to help assess the financial case for solar, an option they initially viewed as “free money.”
The homeowner sought advice in Reddit’s r/SolarDIY community on choosing a suitable solar setup and deciding whether a small installation would be worth the investment. Sunlight reaches the apartment until 5 p.m., they said. Its southeast-to-south orientation and lack of obstructions allow it to receive sun throughout the year.
The household’s limited electricity use raised doubts about the potential savings despite the property’s seemingly favorable location near the 38th parallel.
“Should I install solar, and if yes in what form?” the homeowner asked.
For households considering residential solar, and especially those whose electric company has a net metering or billing policy that allows the home to bank credit for unused solar power during the day, electricity savings can be substantial. Even for those who aren’t ready to spend upfront, $0-down solar leases may save hundreds of dollars per month. EasyHome offers a free explorer tool to estimate potential savings and find vetted local installers.
Commenters calculated the homeowner’s electricity rate at $0.29 per kilowatt-hour, a starting point for estimating the value of solar power used at home. Since the homeowner did not expect the household to use much of the solar power produced during the day, a more complete projection of the outcome from installing solar was especially important.
Oddly, only one commenter mentioned net billing, which is what Greece has for most residential solar users instead of net metering, and they linked to an informational page from Fotergeia about how it works. There is plenty of nuance, but as Fotergeia says, “Whatever you do not consume at the moment it is produced is not lost: it is exported to the grid and credited to your bill in monetary value.”
With energy prices through the roof, there’s never been a better time to go solar — and EasyHome can help you find the best prices from the best installers in your area.
EasyHome takes the guesswork and headaches out of energy upgrades by showing you estimated savings from a network of vetted local partners. To get started, just enter your ZIP and share a few details about your home — seeing your estimate is really that easy.
The homeowner said they had not reviewed it, adding, “if I understand correctly net billing pays wholesale price by 15 minute average, which can be pretty low. I will check it out.”
Even if the country’s net billing policies are not quite a 1:1 value as some net metering systems provide, if the solar panel system is sized right, it could easily produce so much power that it would nonetheles pay for itself in a matter of 7-10 years, as is the typical average with residential rooftop solar. 
“A correctly sized system can cover most of your annual consumption, cutting your electricity bill to a fraction of what it is today,” Fotergeia’s page says of the Greek system.
In any case, the potential savings from solar depend on both the cost of electricity and how much purchased power the panels could replace.
Commenters also recommended using daytime electricity consumption to determine the size of a small solar array. They proposed storing daytime solar output in a battery for later use, which is valuable for any home user and even more so for those without any form of net metering or net billing who also would not use much power during daylight hours.
For those interested in solar facing similar considerations, EasyHome offers options for exploring battery storage alongside solar. Pairing panels with a battery system can help manage electricity costs by saving production for later use and provide backup power during outages.
Other homeowners are also weighing how much solar could save them and whether to add a battery. 
• A homeowner considered whether a portable power station could store surplus midday solar electricity.
• In the U.K., solar users say falling electricity export rates make batteries increasingly important.
• In the U.K., free solar lowered bills, while commenters recommended a bigger storage battery.
Get TCD’s free newsletters for easy tips, smart advice, and a chance to earn $5,000 toward home upgrades. To see more stories like this one, change your Google preferences here.
© 2025 THE COOL DOWN COMPANY. All Rights Reserved. Do not sell or share my personal information. Reach us at hello@thecooldown.com.

source

Posted in Renewables | Leave a comment

Is Tibet’s Solar Power About More Than Renewable Energy? – https://dailyasianage.com/

Published:  08:25 PM, 15 November 2026

Go to Home Page »

source

Posted in Renewables | Leave a comment

Why solar researchers are working to devise a silver reduction playbook – UNSW Sydney

Adobe Stock
Solar cells rely on silver to help generate electricity efficiently, but its rising cost and growing demand mean the renewable energy industry is keen to reduce its use – while not compromising performance.
Solar power may have become one of the world's cheapest sources of renewable electricity, but an increasingly expensive precious metal is creating a challenge for the industry.
Silver, a material commonly associated with jewellery and electronics, plays an important role in helping solar cells generate electricity.
However, its rising price and growing demand are putting pressure on manufacturers, prompting researchers to investigate whether cheaper alternatives can do the same job.
At UNSW Sydney, Dr Ning Song and her research team, working closely with Scientia Professor Martin Green, are exploring ways to reduce the amount of silver used in solar cells, or potentially eliminate it altogether.
For enquiries about this story and interview requests please contact Neil Martin, News & Content Coordinator.
Email: n.martin@unsw.edu.au
The challenge is not simply finding a cheaper material. Any alternative must also help solar panels generate electricity efficiently – and do so reliably for decades, without undermining the affordability and environmental benefits that have helped make solar power so attractive.
Solar panels generate electricity when sunlight hits photovoltaic (PV) cells, usually made from silicon. But producing electricity is only part of the process: that electricity also needs to be collected and transported out of the cell.
Silver performs this important function.
Solar cells contain extremely thin metal lines, called contacts, that collect the electricity generated within the cell. Silver is particularly well suited to this job because it conducts electricity exceptionally well and can be manufactured into fine lines using a relatively straightforward printing process.
These properties help solar cells generate electricity efficiently while minimising the amount of sunlight blocked by the metal contacts.
“Silver is used for the metal contacts that get the current out of the solar cells,” says Dr Song, a Senior Lecturer in UNSW’s School of Photovoltaic and Renewable Energy Engineering.
“It has very good conductivity and is easy to screen print. So silver has been one of the best for performance, but not necessarily moving forward for cost and sustainability.”
Silver is expensive, and its price can fluctuate considerably. Recent price volatility has increased the pressure on manufacturers to reduce the amount used in each solar cell.
And when the price of silver rises, solar manufacturers face higher production costs.
Silver paste, which is used to form the electrical contacts, accounted for up to 30% of the cost of manufacturing a solar cell when silver prices peaked in early 2026, say industry analysts, although the share varies with cell technology, silver prices and paste consumption.
The rising cost of silver is one of the reasons that solar panel manufacturers are accelerating efforts to find alternatives, with researchers such as Dr Song vitally important in the process.
“In academia, we investigate the fundamental mechanisms behind how solar cells work, but we also develop new materials and manufacturing technologies to improve their performance and reduce costs,” she says.
“I think it’s a joint effort. Industry brings extensive manufacturing expertise and the ability to scale up technologies. By working together, we can combine scientific understanding with technological innovation to develop practical solutions for the solar industry.”
As well as the cost issue, silver is a finite resource, and growing demand from photovoltaics and other industries has raised questions about long-term supply.
Mining and processing silver also have environmental impacts, including energy consumption, land disturbance and waste generation. Reducing silver use could help ease pressure on supply and reduce some impacts associated with its extraction.
So the work of Dr Song and others in the field to find a potential alternative to silver in the production of solar cells is becoming ever more important.
Researchers are investigating several alternatives, including aluminium, nickel and copper. Each offers potential advantages, but none is a straightforward replacement.
Aluminium is significantly cheaper than silver and is already used in some solar-cell designs.
Aluminium is also used in established solar-cell metallisation processes, although its suitability depends on the contact structure and the processing conditions.
However, aluminium is less electrically conductive than silver, and the contact interface and firing process must be carefully controlled to avoid additional electrical losses.
Dr Song and colleagues are investigating ways to address these problems by adjusting the composition of aluminium pastes and optimising manufacturing conditions.
The UNSW team is studying how metal-paste formulations, contact interfaces and manufacturing conditions influence electrical losses in silicon solar cells. This work aims to identify practical ways to use less silver while maintaining cell performance.
“We are trying to reduce these losses by tuning the aluminium paste recipe and optimising the firing conditions,” she says.
The aim is to reduce silver use without sacrificing the performance of the finished cell. If successful, this could help manufacturers lower costs while maintaining the efficiency that makes solar panels commercially attractive.
In another study, researchers developed an aluminium paste that could reduce silver use and simplify the manufacturing process for advanced back-contact cells.
UNSW teams have demonstrated aluminium rear contacts in industrially relevant TOPCon solar cells can achieve 22.9% efficiency, compared with 23.7% for silver-contact reference cells. The result shows the potential of aluminium while highlighting the need to further reduce electrical losses.
Copper is another attractive alternative because it is much cheaper than silver while offering similarly strong electrical conductivity.
However, copper can create problems when used in silicon solar cells. It can move into the silicon and interfere with the processes that allow the cell to generate electricity.
“Copper can also oxidise, potentially affecting its electrical performance and long-term reliability,” says Dr Song.
One approach uses silver-coated copper particles to reduce the overall silver content while helping manage oxidation and contact performance. Long-term reliability and process compatibility remain important considerations.
Nickel is also being investigated because it is relatively stable and already has established uses in semiconductor manufacturing.
However, nickel-based contacts can introduce electrical losses and other technical challenges.
In a recent study published in Solar Energy Materials and Solar Cells, Dr Song's team, including PhD researcher Lizhi Sun and Scientia Professor Martin Green, investigated partially replacing silver with nickel in the rear contacts of industrial TOPCon solar cells. With a suitable nickel powder, replacing 10% of the silver powder by weight reduced rear-finger raw-metal costs by 6.8%, with an absolute efficiency decrease of just 0.024 percentage points.
“Replacing silver with nickel is not simply about using a cheaper metal. We need to consider how the nickel powder affects electrical contact performance, printability and the amount of paste consumed during manufacturing,” says Dr Song.
The researchers found that increasing the nickel content could increase paste consumption and largely offset the expected cost savings. Their findings highlight the importance of considering both material properties and manufacturing requirements when developing practical alternatives to silver.
Researchers are continuing to investigate nickel-based pastes and manufacturing processes to determine whether they can deliver the necessary performance and reliability.
Dr Song says there is no single solution to the problem of replacing silver that will work for every solar cell.
“It's really dependent on the cell structure,” Dr Song says. “It's hard to say which material will ultimately prove the most suitable.”
Different solar-cell designs have different manufacturing requirements, meaning a material that works well in one technology may not be suitable for another.
Dr Song believes continued research in partnership with industry could enable substantial reductions in silver use, and potentially silver-free contacts in selected cell technologies, over the coming years. The pace will depend on manufacturing compatibility, performance and long-term reliability.
One of the biggest obstacles to that timeline is reliability. 
Solar panels are expected to operate outdoors for approximately 25 to 30 years, meaning manufacturers must be confident that alternative contacts will withstand prolonged exposure to environmental conditions.
“Although other options may have passed testing in the lab, industry still needs confidence from outdoor testing and that data may not yet be available,” Dr Song says.
“We have to make sure the modules are reliable over the long term so they can work efficiently for many years.”
UNSW 
Sydney NSW 2033 Australia
Telephone: +61 2 93851000

UNSW CRICOS Provider Code: 00098G
TEQSA Provider ID: PRV12055
ABN: 57 195 873 179
UNSW respectfully acknowledges the Bidjigal, Biripai, Dharug, Gadigal, Gumbaynggirr, Ngunnawal and Wiradjuri peoples, on whose unceded lands we are privileged to learn, teach and work. We honour the Elders of these Nations, past and present, and recognise the broader Nations with whom we walk together. UNSW acknowledges the enduring connection of Aboriginal and Torres Strait Islander peoples to culture, community and Country.
The Uluru Statement

source

Posted in Renewables | Leave a comment

OCI Energy Sells Clairemont Solar Project to Hyundai Engineering – News and Statistics – IndexBox

We use cookies to improve your experience and for marketing. Read our cookie policy Manage cookies
Search across reports, market insights, and blog stories.
OCI Energy has agreed to sell Project Clairemont, a 327 MWdc solar development in Kent County, Texas, to Hyundai Engineering Co., Ltd., according to a press release from OCI Energy. The transaction is the second between the two companies and follows OCI Energy’s 2024 sale of the 260 MWdc Project Hillsboro in Hill County, Texas, to Hyundai Engineering.
Representatives of both companies met in San Antonio on Wednesday, November 11, for a ceremony marking the closing of the Clairemont deal. Sabah Bayatli, President of OCI Energy, said the company was proud of its team’s work in advancing the project and noted that its relationship with Hyundai supports its efforts to develop large-scale energy solutions that meet growing power demand.
Minsu Park, Head of Energy Marketing Office at Hyundai Engineering, described Project Clairemont as a significant addition to the company’s renewable energy portfolio in the United States. He said the transaction builds on the trust established through the Hillsboro acquisition and supports Hyundai Engineering’s long-term growth strategy in the U.S. market, where it aims to expand through high-quality projects serving demand for clean and reliable power.
Construction on Project Clairemont is expected to begin in the third quarter of 2027, with completion anticipated in the third quarter of 2029. Sidley Austin LLP represented OCI Energy in the sale, while K&L Gates LLP represented Hyundai Engineering.
OCI Energy is a U.S.-based developer, owner and operator of utility-scale solar and battery energy storage projects. Since 2012, it has advanced a portfolio of projects across key U.S. power markets, covering development through asset management, and reports a multi-gigawatt pipeline.
Hyundai Engineering, established in 1974, is a global engineering and construction company with more than 50 years of experience across the energy, industrial, building and housing, infrastructure, and environmental sectors. The company is expanding its renewable energy portfolio through investments in solar and other energy infrastructure projects.
Interactive table based on the Store Companies dataset for this report.
Report Scope and Analytical Framing
Concise View of Market Direction
Market Size, Growth and Scenario Framing
Commercial and Technical Scope
How the Market Splits Into Decision-Relevant Buckets
Where Demand Comes From and How It Behaves
Supply Footprint and Value Capture
Trade Flows and External Dependence
Price Formation and Revenue Logic
Who Wins and Why
How the Domestic Market Works
Commercial Entry and Scaling Priorities
Where the Best Expansion Logic Sits
Leading Players and Strategic Archetypes
How the Report Was Built
Major US solar manufacturer
Residential & commercial solar
Former Cree LED business
Spin-off from SunPower
Specialty & high-power LEDs
LED technology & solutions
Advanced photonics
Residential solar panels
CIGS solar technology
US & Canadian manufacturing
North American manufacturing
US-made solar panels
US operations of Korean parent
3D architecture LEDs
High-quality lighting
High-brightness microdisplays
Disinfection & purification
US crystalline silicon solar
Next-generation tandem cells
Tandem cell technology
Manufacturing equipment
Turnkey production lines
Distributor & assembler
Residential & commercial
Former Philips business
Specialty & horticultural
Military & commercial
Aluminum nitride substrates
Materials for UV LEDs
US division of Kyocera
Tell us where to send the sample and whether you want this report customized.
Thank you. Our team will review your request and reply to your business email.
Our team will review your request and route it to support@indexbox.io.
IndexBox, Inc.
2093 Philadelphia Pike #1441
Claymont, DE 19703, USA
Contact us
© 2026 IndexBox, Inc
Instant access. No credit card needed.
Online access to 2M+ reports, dashboards, and tables. Trusted by Fortune 500 teams.
Free Data: Solar Cells and Light-Emitting Diodes — United States
Instant access. No credit card needed.

source

Posted in Renewables | Leave a comment

Oregon solar owner says fall bills went 'nuts' after a second battery cut grid credits – The Cool Down

© 2025 THE COOL DOWN COMPANY. All Rights Reserved. Do not sell or share my personal information. Reach us at hello@thecooldown.com.
Some people noted that energy lost during battery charging and discharging could also affect savings.
Photo Credit: iStock
Adding a second home battery may seem like a useful way to make the most of rooftop solar. For one Oregon homeowner, however, the upgrade meant fewer electricity credits heading into fall and power bills that went “nuts.”
The homeowner in Hood River, Oregon, turned to a Reddit community to ask whether installing a second home battery was worth the reduced electricity credits sent back to the grid.
“It seems the 2nd battery isn’t worth the grid credits,” the original poster wrote. “Anyone else have this conundrum?”
When solar production drops, the homeowner can draw on credits earned from earlier exports. The utility credits exported electricity at a one-for-one rate and does not charge more during peak hours, the homeowner explained.
For homeowners weighing similar purchases, EnergySage offers a way to explore battery products and compare competitive installation estimates, with utility billing arrangements an important consideration.
EnergySage also partners with electrification company Qmerit, with the stated goal of helping homeowners find the best available battery-storage pricing.
The OP had set the system to self-consumption mode with a 20% reserve, allowing most of the stored electricity to power the house rather than remain available for outages.
A California commenter with two 5P batteries prioritized using solar power at home because their utility offered little compensation for exports.
With energy prices through the roof, there’s never been a better time to go solar — and EasyHome can help you find the best prices from the best installers in your area.
EasyHome takes the guesswork and headaches out of energy upgrades by showing you estimated savings from a network of vetted local partners. To get started, just enter your ZIP and share a few details about your home — seeing your estimate is really that easy.
Stored electricity typically kept that home running overnight. During the day, the batteries reached full charge by midday, and surplus solar generation supplied electric vehicles.
Another commenter encouraged the OP to compare household electricity use across summers. Others noted that energy lost during battery charging and discharging could also affect savings.
Beyond potential bill savings, the additional storage could give the OP more backup power during outages and greater energy independence. Appropriately configured systems can also support off-grid use.
Several commenters suggested raising the OP’s reserve setting so the household would use less stored electricity each day.
One recommended keeping 85% to 100% available for outages. Another suggested limiting discharge to the amount of energy used by the original single-battery setup.
The OP had not reported whether any changes helped. They were considering a 60% or 70% reserve and testing a schedule that would charge the batteries from the grid in the early morning and prevent discharge until sunset.
For households seeking a smaller backup option, Pila offers a plug-and-play alternative at a substantially lower price point than whole-home backup systems.
The California commenter also suggested trying the savings profile if the OP wanted to prioritize exports, rather than staying in self-consumption mode.
Whether a home battery pays off depends in part on your utility’s rates and solar export credits, as many homeowners have found.
• A solar homeowner’s bill barely changed after export rates dropped, prompting suggestions to add batteries.
• A Connecticut homeowner said solar credits vanished despite higher output, raising concerns about buyback arrangements.
• California’s 80% export credit cut steers new solar buyers toward batteries costing over $14,000.
Get TCD’s free newsletters for easy tips, smart advice, and a chance to earn $5,000 toward home upgrades. To see more stories like this one, change your Google preferences here.
© 2025 THE COOL DOWN COMPANY. All Rights Reserved. Do not sell or share my personal information. Reach us at hello@thecooldown.com.

source

Posted in Renewables | Leave a comment

Turkiye, China Sign $15B Renewable Energy Deal at COP31 – News and Statistics – IndexBox

We use cookies to improve your experience and for marketing. Read our cookie policy Manage cookies
Search across reports, market insights, and blog stories.
Turkiye and China have signed a memorandum of understanding valued at roughly $15 billion for new renewable energy installations and electricity infrastructure in Turkiye, according to pv magazine. The agreement was concluded between Turkiye’s Ministry of Energy and Natural Resources and China’s National Energy Administration on the sidelines of COP31, which is being held in the Turkish city of Antalya and runs until November 20.
Turkiye’s Energy and Natural Resources Minister Alparslan Bayraktar said the agreement is intended to deliver 7 GW of new solar and wind power plants, along with new energy storage systems and 4 GW of electricity transmission infrastructure. He characterized the deal as part of Turkiye’s recently announced national energy vision for 2040, which targets 175 GW of solar and wind capacity by the end of the next decade, building on an earlier goal of 125 GW by 2035.
Additional details on the projects, including a development timeline, have not yet been released.
The memorandum follows the signing earlier this week of eight financial agreements supporting the development of 2 GW of solar in Turkiye. Those projects fall under a cooperation agreement with Saudi Arabia covering a total of 5 GW of new renewables.
Turkiye’s cumulative solar capacity reached approximately 26.9 GW by the end of the first half of 2026, after additions of 2.1 GW during the first six months of the year and 4.7 GW across 2025.
Interactive table based on the Store Companies dataset for this report.
Report Scope and Analytical Framing
Concise View of Market Direction
Market Size, Growth and Scenario Framing
Commercial and Technical Scope
How the Market Splits Into Decision-Relevant Buckets
Where Demand Comes From and How It Behaves
Supply Footprint, Trade and Value Capture
Trade Flows and External Dependence
Price Formation and Revenue Logic
Who Wins and Why
Where Growth and Supply Concentrate
Commercial Entry and Scaling Priorities
Where the Best Expansion Logic Sits
Leading Players and Strategic Archetypes
Detailed View of the Most Important National Markets
How the Report Was Built
Largest solar manufacturer globally
Leading monocrystalline silicon producer
Major module and cell producer
High-efficiency cell and module maker
Global manufacturer and project developer
Major player in US and EU markets
Integrated PV product manufacturer
Leading thin-film CdTe manufacturer
World's largest solar cell producer
ABC cell technology leader
Major LED component and display maker
Pioneer and major supplier of LED chips
Historically leading innovator in LED technology
Leading European optoelectronics supplier
High-power LED and automotive lighting
One of world's largest LED chip producers
Major LED packaging and component supplier
Leading Taiwanese LED chip manufacturer
Innovator in WICOP and SunLike technologies
LED components for automotive and IT
IBC cell technology leader
Solar project developer and manufacturer
Integrated PV manufacturer
Historically significant in both fields
Rapidly growing cell and module producer
Solar manufacturing arm of Chint Group
Module manufacturer with US focus
Leading Indian solar manufacturer
LED packaging and lighting solutions
Major LED packaging company
Tell us where to send the sample and whether you want this report customized.
Thank you. Our team will review your request and reply to your business email.
Our team will review your request and route it to support@indexbox.io.
IndexBox, Inc.
2093 Philadelphia Pike #1441
Claymont, DE 19703, USA
Contact us
© 2026 IndexBox, Inc
Instant access. No credit card needed.
Online access to 2M+ reports, dashboards, and tables. Trusted by Fortune 500 teams.
Free Data: Solar Cells and Light-Emitting Diodes — World
Instant access. No credit card needed.

source

Posted in Renewables | Leave a comment