Water-Film Cooling Reduces Photovoltaic Backsheet Temperatures Across Outdoor Testing Days – Bioengineer.org

Water-Film Cooling Reduces Photovoltaic Backsheet Temperatures Across Outdoor Testing Days
An outdoor experimental investigation has evaluated the thermal and electrical performance of front-surface water-film cooling and rear-mounted aluminum heat sinks applied to polycrystalline photovoltaic modules. Across nine monitoring days, the active water-film cooling system produced daily maximum backsheet temperature reductions ranging from 8.5 °C to 18.96 °C when compared directly against an uncooled reference module. During a designated representative active test day, the maximum temperature recorded on the backsheet of the water-film configuration reached 42.0 °C, whereas the reference module reached 50.5 °C under the same exposure, establishing an operational temperature difference of 8.5 °C.
To systematically compare active and passive thermal management approaches in real operating environments, the investigators installed two identical polycrystalline photovoltaic modules sharing the same commercial model specifications, each rated at 100 Wp. The experimental setup was monitored continuously from November 2025 through March 2026, capturing operating temperature, voltage, and current measurements at regular one-minute intervals throughout the testing campaign.
In evaluating the active configuration, the researchers accounted for both the gross electrical production and the parasitic energy required to sustain fluid circulation across the front surface of the module. Over the course of the representative active test, the dedicated water pump consumed 22.89 Wh of electrical energy. This reported pump consumption accounted strictly for the pumping unit itself, explicitly excluding power-supply losses and control-system consumption. After subtracting this operational pumping expenditure, the active water-film setup delivered 475.05 Wh of net electrical energy during the test day.
The uncooled reference module generated 438.06 Wh of electrical energy over the equivalent active monitoring period, yielding a net electrical energy difference of 8.44% in favor of the active water-film system. In contrast, the passive thermal management trial examined a configuration featuring rear-mounted aluminum heat sinks fitted with cooling fins. During the representative passive test, the finned heat-sink module recorded a maximum backsheet temperature that was only 1.50 °C below that of the uncooled reference module, indicating a much smaller thermal suppression than that achieved by surface liquid cooling.
The passive heat-sink configuration also showed limited electrical output advantages under outdoor conditions. Over its representative test day, the heat-sink module registered a daily electrical energy difference of 1.70% relative to the uncooled reference panel. Crucially, the authors determined that this 1.70% energy difference was smaller than the reported expanded uncertainty of the measurement system. As a result, the measured electrical change from the rear-mounted aluminum heat sink could not be reliably distinguished from experimental measurement variability.
A primary limitation identified in the study centers on the electrical loading mechanisms applied to the respective solar modules. Throughout the experiments, the investigated test module was operated using maximum power point tracking, whereas the reference module was connected to a fixed resistive load. Consequently, the observed differences in electrical energy output reflect the combined influence of thermal cooling and electrical load management rather than thermal dissipation alone, preventing researchers from attributing the power gains exclusively to temperature reduction.
Finally, the authors noted that environmental discrepancies prevented a direct comparative ranking between the two cooling technologies. Although the front-surface water-film cooling demonstrated substantially greater temperature suppression than the rear-mounted heat sinks under their respective test scenarios, the active and passive experimental trials took place on different calendar days.
Subject of Research: Outdoor active and passive cooling performance on polycrystalline photovoltaic modules
Article Title: Experimental assessment of active and passive cooling configurations for photovoltaic modules under outdoor conditions
Article References: Martins, G., Bandarra Filho, E. P., Martins, L. C., Carrillo Pabon, Y., & Andrade, J. R. (2026). Experimental assessment of active and passive cooling configurations for photovoltaic modules under outdoor conditions. Frontiers in Thermal Engineering, 6, Article 1970235. https://doi.org/10.3389/fther.2026.1970235
Image Credits: AI Generated
DOI: 10.3389/fther.2026.1970235
Keywords: photovoltaic modules, water-film cooling, aluminum heat sinks, active cooling, passive cooling, thermal management, backsheet temperature, maximum power point tracking, fixed resistive load, net electrical energy, polycrystalline solar cells, pump consumption, outdoor monitoring, expanded uncertainty, temperature reduction, load management, Federal University of Uberlandia
News Source: Denise Maddox. (November 17, 2026). Water-Film Cooling Reduces Photovoltaic Backsheet Temperatures Across Outdoor Testing Days. Scienmag.
We bring you the latest biotechnology news from best research centers and universities around the world. Check our website.
Enter your email address to subscribe to this blog and receive notifications of new posts by email.


Bioengineer.org © Copyright 2023 All Rights Reserved.
Login to your account below




Please enter your username or email address to reset your password.


Bioengineer.org © Copyright 2023 All Rights Reserved.

source

This entry was posted in Renewables. Bookmark the permalink.

Leave a Reply