Simulations Show Lead-Free Perovskite Solar Cell Architecture Could Reach 32.41% Efficiency – Bioengineer.org

Simulations Show Lead-Free Perovskite Solar Cell Architecture Could Reach 32.41% Efficiency
A computational investigation has identified an optimized material architecture for lead-free perovskite solar cells that achieves a simulated power conversion efficiency of 32.41 percent under standard illumination conditions. Researchers modeled a planar n-i-p photovoltaic configuration incorporating cesium tin-germanium tri-iodide as the active light-harvesting layer, demonstrating that an entirely inorganic combination of charge transport materials drastically outperforms conventional organic transport layers. By pairing an electron-extracting layer of zinc oxide at the front transparent contact with a hole-extracting layer of nickel oxide at the rear metallic contact, the modeled device attained a short-circuit current density of 28.38 milliamperes per square centimeter, an open-circuit voltage of 1.35 volts, and a fill factor of 84.54 percent under standard AM1.5G solar radiation operating at 1000 watts per square meter.
The motivation behind the modeling effort stems from pressing environmental and stability challenges associated with conventional lead-halide perovskite solar cells, such as methylammonium lead iodide. Although traditional lead-based formulations have demonstrated experimental power conversion efficiencies exceeding 25 percent, lead remains a toxic heavy metal capable of leaching into natural ecosystems and accumulating within biological food chains far more readily than other common industrial lead sources. Consequently, materials scientists have actively sought non-toxic alternatives derived from less hazardous elements. Bivalent tin and germanium cations present viable structural analogues capable of replacing lead within the perovskite crystal lattice, offering favorable electronic characteristics while mitigating toxicological hazards.
Despite their environmental appeal, single-cation tin or germanium absorbers encounter acute chemical vulnerabilities when exposed to ambient working conditions. Pure tin-based perovskites, which possess near-optimal bandgaps of roughly 1.3 electronvolts alongside high charge-carrier mobilities, undergo rapid oxidation from bivalent tin to tetravalent tin under ambient air. This oxidation process generates crystal vacancies and induces unwanted intrinsic p-type self-doping. Similarly, germanium-based perovskites tend to suffer from facile bivalent germanium oxidation, low photocurrent yields, and poor overall stability. By synthesizing mixed tin-germanium compositions, specifically cesium tin-germanium tri-iodide, researchers harness the complementary benefits of both elements. Previous experimental work demonstrated that an all-inorganic version of this mixed absorber forms a protective native-oxide surface layer that passivates structural defects, preserving roughly 90 percent of its initial efficiency after 500 hours of operation. With an estimated bandgap spanning 1.4 to 1.5 electronvolts and strong optical absorption, the mixed absorber presents theoretical performance limits approaching the 33 percent Shockley-Queisser threshold.
To explore how surrounding device layers influence charge extraction from this absorber, researchers conducted a comprehensive one-dimensional simulation using the SCAPS-1D software framework. Computational modeling provides a rigorous mechanism for evaluating solar cell prototypes without the extensive development timelines, fabrication expenses, and material hazards associated with experimental trial-and-error chemistry. The simulator operates by solving coupled Poisson and continuity semiconductor transport equations under steady-state illumination, tracking carrier generation, recombination dynamics, and drift-diffusion currents across heterojunction interfaces. The baseline device layout consisted of an indium-tin-oxide transparent front electrode with a work function of 4.2 electronvolts, an electron transport layer, a 1.0-micrometer-thick cesium tin-germanium tri-iodide absorber, a hole transport layer, and a gold rear electrode with a work function of 5.0 electronvolts.
Within the simulation matrix, the active perovskite absorber maintained a fixed p-type acceptor doping concentration of 10¹⁵ per cubic centimeter, an internal defect density of 10¹⁴ per cubic centimeter, and an optical bandgap of approximately 1.5 electronvolts. Researchers then systematically compared nine distinct device combinations by pairing three separate electron transport materials against three individual hole transport materials. The evaluated electron transport layers comprised organic [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) alongside inorganic metal oxides, specifically zinc oxide and titanium dioxide. The evaluated hole transport candidates included organic poly(triarylamine) (PTAA), poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS), and inorganic nickel oxide, with all hole transport films modeled at a standardized thickness of 400 nanometers and doping concentrations ranging between 10¹⁴ and 10¹⁹ per cubic centimeter.
The comparative evaluation revealed that inorganic electron transport layers dramatically surpass organic PCBM in electrical and optical performance. Both zinc oxide and titanium dioxide feature wide optical bandgaps of approximately 3.3 and 3.2 electronvolts, respectively, resulting in conduction band minima that position favorably above the conduction band of the perovskite absorber. This favorable energy band alignment establishes a smooth electron-collection pathway while imposing a steep energy barrier that blocks holes, effectively quenching undesirable surface recombination at the front transparent contact. Furthermore, because zinc oxide and titanium dioxide are exceptionally transparent across the visible spectrum, fewer incident photons are parasitically absorbed within the transport layer, permitting greater illumination to reach the perovskite core. Consequently, zinc oxide and titanium dioxide architectures maintained high quantum efficiency out to 820 nanometers and produced short-circuit current densities near 28 milliamperes per square centimeter, whereas PCBM configurations were restricted to approximately 25 milliamperes per square centimeter due to narrower optical transmission and inferior hole-blocking characteristics.
Parallel evaluations of hole transport candidates established that inorganic nickel oxide provides superior charge collection compared to organic alternatives. Featuring a wide bandgap of roughly 3.8 electronvolts and a deep valence band edge positioned near 5.4 electronvolts, nickel oxide facilitates seamless hole transfer from the perovskite valence band while erecting a formidable physical barrier against unwanted electron leakage toward the back electrode. When paired with titanium dioxide, a nickel oxide hole transport layer achieved an open-circuit voltage of approximately 1.3573 volts and an efficiency of 32.39 percent. Conversely, devices incorporating PEDOT:PSS exhibited significantly depressed open-circuit voltages of roughly 1.1984 volts and efficiencies of 27.87 percent, driven by a narrower optical bandgap, lower work function, and interfacial trap formation. Devices employing PTAA attained an intermediate efficiency of 32.09 percent, limited by moderate hole mobility and a conduction band alignment that permitted greater electron leakage toward the front interface.
Detailed band diagram analyses across all nine modeled permutations confirmed that carrier collection relies heavily on proper quasi-Fermi level alignment across heterojunctions. In the optimal configurations, the electron quasi-Fermi level aligned seamlessly across the absorber-electron transport boundary, guiding photogenerated electrons downhill toward the front indium-tin-oxide electrode. Simultaneously, the hole quasi-Fermi level matched the valence band edge of the hole transport layer, funneling positive charges toward the gold rear contact. The overall champion architecture, comprising indium tin oxide, zinc oxide, cesium tin-germanium tri-iodide, nickel oxide, and gold, established the highest simulated power conversion efficiency at 32.41 percent. Titanium dioxide delivered nearly identical electrical outcomes, producing an efficiency of 32.39 percent, reflecting the nearly identical bandgap and band-edge positions shared between the two inorganic metal oxides.
Beyond baseline layer selection, researchers evaluated the influence of parasitic electrical resistances on photovoltaic conversion. Series resistance, stemming from internal film resistivity and interfacial contact barriers, was varied from 0 to 10 ohm-square-centimeters while keeping shunt resistance fixed at 10⁵ ohm-square-centimeters. The simulations demonstrated that while series resistance produces negligible effects on short-circuit current and open-circuit voltage, it severely degrades the fill factor and total power output. With zero series resistance, the optimized configuration yielded a fill factor of approximately 84 percent; introducing 1 ohm-square-centimeter reduced the fill factor to 83 percent, and increasing resistance to 10 ohm-square-centimeters caused the fill factor to collapse below 70 percent. Parametric testing of shunt resistance, which models unwanted current leakage through pinholes and grain boundaries, revealed that device efficiency drops precipitously when shunt resistance falls below 10³ ohm-square-centimeters, whereas maintaining shunt resistance at or above 10⁵ ohm-square-centimeters successfully suppresses recombination pathways and preserves maximum open-circuit voltages.
Finally, thermal investigations conducted across operating temperatures spanning 300 to 350 Kelvin demonstrated that lead-free cesium tin-germanium tri-iodide solar cells remain susceptible to thermal degradation common across semiconductor devices. However, reverse saturation dark currents expanded exponentially with rising thermal energy, leading to a linear decline in open-circuit voltage of several millivolts per Kelvin and reducing absolute conversion efficiency by 2 to 4 percent across the 50-Kelvin span. While the modeled 32.41 percent efficiency reflects idealized laboratory assumptions featuring pristine interfaces and low defect densities that exceed current experimental prototypes spanning 7 to 15 percent, the simulation provides explicit quantitative architectural roadmaps to guide future laboratory synthesis of environmentally sustainable, high-efficiency photovoltaics.
Subject of Research: Numerical modeling and interface optimization of lead-free cesium tin-germanium tri-iodide perovskite solar cells
Article Title: Optimization of multiple ETL and HTL layers for high-performance lead-free CsSnGeI₃-based perovskite solar cells: a simulation study
Article References: Konch, P., Singha, P., Kalita, P. K., Bhattarai, S., & DasMahapatra, S. (2026). Optimization of multiple ETL and HTL layers for high-performance lead-free CsSnGeI₃-based perovskite solar cells: a simulation study. Materials for Renewable and Sustainable Energy, 15(2), Article 26. https://doi.org/10.1007/s40243-026-00371-9
Image Credits: AI Generated
DOI: 10.1007/s40243-026-00371-9
Keywords: perovskite solar cells, lead-free perovskites, CsSnGeI3, SCAPS-1D, solar cell simulation, electron transport layer, hole transport layer, zinc oxide, nickel oxide, power conversion efficiency, photovoltaics, band alignment, series resistance, shunt resistance, thermal sensitivity, renewable energy
News Source: Denise Maddox. (November 21, 2026). Simulations Show Lead-Free Perovskite Solar Cell Architecture Could Reach 32.41% Efficiency. Scienmag.
We bring you the latest biotechnology news from best research centers and universities around the world. Check our website.
Enter your email address to subscribe to this blog and receive notifications of new posts by email.


Bioengineer.org © Copyright 2023 All Rights Reserved.
Login to your account below




Please enter your username or email address to reset your password.


Bioengineer.org © Copyright 2023 All Rights Reserved.

source

This entry was posted in Renewables. Bookmark the permalink.

Leave a Reply