Simulated Carbon Nanotube Interlayers Boost Lead-Free Perovskite Solar Efficiency to 29 Percent – Bioengineer.org

Simulated Carbon Nanotube Interlayers Boost Lead-Free Perovskite Solar Efficiency to 29 Percent
A computational investigation using the SCAPS-1D simulation framework demonstrates that introducing a single-walled carbon nanotube interlayer into a lead-free barium tin sulfide perovskite solar cell can substantially elevate its power conversion efficiency to 29.15 percent. Starting from an optimized baseline device comprising fluorine-doped tin oxide, a titanium dioxide electron transport layer, a barium tin sulfide absorber layer, a poly(3-hexylthiophene-2,5-diyl) hole transport layer, and a silver back contact, the researchers established an initial baseline efficiency of 26.05 percent. By positioning an engineered single-walled carbon nanotube layer between the titanium dioxide electron transport layer and the barium tin sulfide absorber, the simulated architecture achieved an absolute efficiency gain of 3.10 percentage points, accompanied by significant enhancements in fill factor and short-circuit current density under standard AM1.5G terrestrial illumination.
The underlying motivation for the study centers on resolving the persistent environmental and operational durability challenges that currently hinder the widespread commercialization of conventional metal-halide perovskites. Although lead-based halide perovskites have achieved rapid technological maturation and high laboratory efficiencies over the past decade, their reliance on toxic lead and their susceptibility to moisture, heat, and chemical degradation remain significant barriers. Chalcogenide perovskites with the general formula ABS3, where barium occupies the A-site and tin occupies the B-site while sulfur substitutes for halogens, have emerged as robust, non-toxic alternatives. Among these materials, barium tin sulfide exhibits intrinsic chemical and thermal stability alongside an optimal direct bandgap between 1.4 and 1.6 electron-volts, which closely matches the requirements of single-junction terrestrial photovoltaics. Nevertheless, translating the advantageous optoelectronic properties of barium tin sulfide into highly efficient photovoltaic devices requires addressing severe interfacial recombination losses, contact energetics, and carrier collection limitations that commonly suppress experimental and simulated device performance.
To establish a rigorous performance benchmark prior to evaluating interfacial modifications, the authors carried out a systematic numerical optimization of the absorber thickness within the baseline heterojunction architecture. In this baseline configuration, the titanium dioxide electron transport layer thickness was held at 50 nanometers and the hole-transporting polymer layer at 200 nanometers, while the barium tin sulfide absorber thickness was varied across a broad range from 50 to 3000 nanometers. The simulation revealed that the power conversion efficiency rose steadily with increasing absorber thickness up to an optimum of 2000 nanometers, reaching 26.05 percent with a short-circuit current density of 27.48 milliamperes per square centimeter, an open-circuit voltage of 1.14 volts, and a fill factor of 83.46 percent.
The electronic viability of this baseline structure was confirmed through a detailed evaluation of its staggered heterojunction band alignment and equilibrium carrier distributions. Using documented material parameters, the conduction band minimum and valence band maximum were determined from electron affinities and bandgap values across every functional layer. The calculated conduction band offset at the titanium dioxide and barium tin sulfide interface was approximately 0.1 electron-volts, providing an effective thermodynamic driving force for electron extraction into the electron transport layer without forming an obstructive energetic barrier. Simultaneously, the valence band offset at the barium tin sulfide and polymer interface was determined to be approximately 0.5 electron-volts, ensuring selective hole collection. Steady-state spatial carrier profiles confirmed that the titanium dioxide layer maintained an elevated electron density of roughly 1.4 times ten to the fourteenth per cubic centimeter while suppressing hole concentration to 9.3 times ten to the eighth per cubic centimeter, validating its intended hole-blocking and electron-selective behavior.
Building upon the optimized baseline parameters, the researchers introduced a single-walled carbon nanotube interlayer at the interface between the titanium dioxide and barium tin sulfide layers to investigate its potential for mitigating interfacial losses. The thickness of this nanocarbon interlayer was systematically swept from 5 to 1000 nanometers while keeping the barium tin sulfide absorber at its optimized thickness of 2000 nanometers. The resulting photovoltaic metrics demonstrated that the power conversion efficiency increased sharply from 27.63 percent at thin interlayer dimensions to a definitive peak of 29.15 percent at an optimal nanotube thickness of approximately 260 nanometers. Across this entire thickness range, the open-circuit voltage remained remarkably stable between 1.13 and 1.14 volts, indicating that the efficiency enhancement was predominantly driven by improvements in transport dynamics and charge collection. When the nanotube layer exceeded 260 nanometers, the internal resistance escalated markedly, triggering pronounced reductions in fill factor, current collection, and overall device efficiency.
A rigorous deconvolution of the simulated device physics revealed that the performance enhancement generated by the carbon nanotube interlayer stems from simultaneous electronic and optical mechanisms. Electron concentration within the optimized nanotube layer reached approximately 1.1 times ten to the twentieth per cubic centimeter, establishing a highly conductive electrical pathway that minimized resistive losses and propelled the fill factor from 83.46 percent in the baseline device to 86.19 percent. Optically, the nanotube network functioned beyond a passive transport intermediary by extending the photoactive collection bandwidth. External quantum efficiency spectra revealed three distinct absorption edges corresponding to titanium dioxide at 388 nanometers, barium tin sulfide at 810 nanometers, and the carbon nanotube layer at 1120 nanometers. Because the nanotubes absorb sub-bandgap photons in the near-infrared spectrum between 810 and 1120 nanometers while remaining largely transparent to shorter wavelengths, they contributed supplementary photocurrent that outweighed parasitic shading losses, raising short-circuit current density from 27.48 to 29.80 milliamperes per square centimeter.
To uncover the electrostatic origins of this improved carrier collection, the researchers carried out capacitance-voltage and Mott-Schottky analyses across the simulated structures. Capacitance remained steady under small bias voltages, registering approximately 9.8 nanofarads per square centimeter for the baseline cell and 5.4 nanofarads per square centimeter for the nanotube-modified configuration, before exhibiting steep rises at forward voltages of 0.8 volts and 1.0 volts, respectively. Linear extrapolation of the Mott-Schottky plots revealed a decisive increase in built-in potential, which rose from 0.70 volts in the unmodified baseline device to 0.93 volts following the insertion of the carbon nanotube interlayer. This substantial elevation in built-in potential deepens interfacial band bending and intensifies the internal electric field across the active junction, thereby accelerating the spatial separation of photogenerated electron-hole pairs, reducing interface recombination, and ensuring efficient directional carrier drift toward their respective selective contacts.
The study also evaluated the spectral response and operational consistency of the carbon nanotube-engineered heterojunction across diverse illumination conditions, including AM0, AM0.2, AM0.4, AM0.8, AM1, and standard terrestrial AM1.5G spectra. Under outer-space and reduced solar spectra ranging from AM0 to AM0.8, the simulated solar cells exhibited exceptionally low short-circuit current densities and correspondingly modest conversion efficiencies, despite maintaining stable open-circuit voltages and high fill factors. The authors explained that this behavior does not signify device degradation or operational failure, but directly reflects the deliberate design of the absorber stack for terrestrial conditions. In the AM0 spectrum, the incident photon distribution shifts predominantly toward higher energies while offering diminished photon flux in the visible and near-infrared wavelengths where barium tin sulfide and carbon nanotubes absorb. Consequently, the architecture demonstrates predictable optical scaling, confirming that its 29.15 percent efficiency ceiling is specifically attuned to terrestrial solar irradiance.
To evaluate whether the simulated gains depended excessively on optimistic physical assumptions, the investigators conducted a comprehensive sensitivity analysis focused on the electron mobility of the carbon nanotube interlayer. While the primary model assigned an upper-bound mobility of 80,000 square centimeters per volt-second characteristic of pristine isolated nanotubes, practical solution-processed thin films routinely exhibit lower effective mobilities between 10 and 1000 square centimeters per volt-second due to bundle formation, defects, and inter-tube junction resistances. By varying mobility across more than three orders of magnitude, the simulation revealed that device efficiency scaled moderately from 27.61 percent at the most conservative mobility of 10 square centimeters per volt-second to 29.15 percent at the maximum value. Even under the lowest evaluated mobility, the device maintained a 1.56 percentage point advantage over the baseline, confirming that the performance enhancement is an intrinsically robust consequence of the interlayer architecture rather than a numerical artifact.
Thermodynamic benchmarking places the 29.15 percent simulated efficiency at roughly 88 percent of the theoretical Shockley-Queisser detailed-balance limit of approximately 33 percent for a 1.53 electron-volt absorber, while surpassing earlier BaSnS3 modeling benchmarks of 25.93 percent by 3.22 percentage points. However, the authors explicitly emphasize the idealized nature of their one-dimensional drift-diffusion model, which omitted series resistance and assumed infinite shunt resistance, abrupt defect-free interfaces, and low bulk trap densities. Moving from simulation to experimental fabrication presents major challenges, including depositing uniform, transparent 260-nanometer nanotube films without aggregation, synthesizing phase-pure stoichiometric barium tin sulfide atop nanocarbon layers, and verifying interfacial chemical stability under heat, moisture, and prolonged operational illumination. The study concludes that experimentalists should initially explore ultra-thin nanotube coatings under 50 nanometers and develop compatible low-temperature deposition routes to translate these simulated interface design principles into physical, lead-free chalcogenide solar cells.
Subject of Research: Numerical simulation of single-walled carbon nanotube interface engineering in lead-free BaSnS3 perovskite solar cells
Article Title: Interface engineering with single-walled carbon nanotubes for high-efficiency (> 29%) lead-free BaSnS₃ perovskite solar cells: insights from numerical simulation
Article References: Mehrabian, M., Norouzzadeh, P., Taleb-Abbasi, M., Azizova, A. N., Mahmoudi, G., & Akhavan, O. (2026). Interface engineering with single-walled carbon nanotubes for high-efficiency (> 29%) lead-free BaSnS₃ perovskite solar cells: insights from numerical simulation. Materials for Renewable and Sustainable Energy, 15(2), Article 28. https://doi.org/10.1007/s40243-026-00364-8
Image Credits: AI Generated
DOI: 10.1007/s40243-026-00364-8
Keywords: BaSnS3, Perovskite solar cells, Lead-free photovoltaics, Single-walled carbon nanotubes, Interface engineering, SCAPS-1D, Power conversion efficiency, Chalcogenide perovskites, Built-in potential, Mott-Schottky analysis, Electron transport layer, Carrier mobility, Near-infrared absorption, Photovoltaic simulation, Shockley-Queisser limit, Drift-diffusion modeling
News Source: Denise Maddox. (November 21, 2026). Simulated Carbon Nanotube Interlayers Boost Lead-Free Perovskite Solar Efficiency to 29 Percent. Scienmag.
We bring you the latest biotechnology news from best research centers and universities around the world. Check our website.
Enter your email address to subscribe to this blog and receive notifications of new posts by email.


Bioengineer.org © Copyright 2023 All Rights Reserved.
Login to your account below




Please enter your username or email address to reset your password.


Bioengineer.org © Copyright 2023 All Rights Reserved.

source

This entry was posted in Renewables. Bookmark the permalink.

Leave a Reply