Iron Substitution in Perovskite Photoanodes Boosts Dye-Sensitized Solar Cell Efficiency – Bioengineer.org

Iron Substitution in Perovskite Photoanodes Boosts Dye-Sensitized Solar Cell Efficiency
Materials scientists have demonstrated a notable performance enhancement in third-generation dye-sensitized solar cells by integrating iron into the crystal lattice of complex perovskite photoanodes. The experimental study, documented in Materials for Renewable and Sustainable Energy, details how altering the transition metal occupying the B-site of Sr0.7Sm0.3BO2.89 perovskites dramatically reshapes their optoelectronic and structural behavior. By substituting cobalt with iron, the research team achieved an overall power conversion efficiency of 6.24 percent in dye-sensitized solar cells employing the iron-based photoanode, designated as SSF. This output marks an improvement of approximately 109 percent compared to identical photovoltaic architectures fabricated with cobalt-based photoanodes, known as SSC, which registered a conversion efficiency of 2.98 percent. The iron-modified perovskite devices also exceeded the 4.76 percent efficiency achieved by standard reference cells constructed with conventional titanium dioxide photoanodes, pointing to a viable pathway for upgrading dye-sensitized solar technologies through targeted cation engineering.
Dye-sensitized solar cells have sustained substantial scientific attention among emerging clean energy harvesting platforms because of their comparatively mild environmental impact, straightforward fabrication protocols, structural flexibility, and low raw material expenses. Despite these inherent advantages, commercial implementation has been hindered because the power conversion efficiency of standard dye-sensitized systems generally lags behind conventional silicon-based solar panels, which routinely attain commercial efficiencies near 25 percent. In a typical dye-sensitized solar cell architecture, the photoanode plays an indispensable role by supporting the dye sensitizer, harvesting incoming photons, and extracting photoexcited electrons before transferring them into a transparent conducting oxide electrode. For decades, nanocrystalline titanium dioxide has functioned as the standard semiconductor baseline; however, its widespread utility is intrinsically constrained by sluggish electron mobility, rapid recombination of separated charge carriers, and an expansive energy bandgap of 3.2 electron volts that severely restricts absorption within the visible light spectrum.
To overcome the electronic and optical limitations associated with traditional wide-bandgap semiconductors, solid-state chemists have turned toward ABO3-type perovskite oxides as alternative photoanode candidates. These crystalline materials possess an adaptable cubic-derived framework wherein larger alkali earth or rare-earth metal cations occupy the central A-site, transition metal cations reside at the eight corner B-sites, and oxygen anions populate the face-centered positions. This compositional versatility permits extensive elemental tuning to tailor lattice parameters, optical absorption profiles, and interfacial carrier dynamics for specialized optoelectronic deployments. Although perovskites historically encountered practical hurdles surrounding thermal instability and ultraviolet-induced chemical breakdown, embedding them as tailored photoanodes in dye-sensitized solar cell environments circumvents several degradation pathways common to classical perovskite photovoltaics. By establishing tailored semiconductor-electrolyte interfaces, researchers can harness the superior optoelectronic properties of perovskites within a chemically resilient, hybrid device configuration.
In the reported experimental protocol, researchers synthesized both Sr0.7Sm0.3FeO2.89 and Sr0.7Sm0.3CoO2.89 perovskite powders through a mechanized ball-milling route to guarantee homogeneous mechanical mixing. Stoichiometric quantities of metal acetylacetonate precursors, encompassing strontium(II), samarium(III), iron(III), and cobalt(III) complexes, were loaded into a 250-milliliter hardened stainless-steel milling container alongside nine-millimeter stainless-steel grinding balls maintaining an eight-to-one ball-to-mass ratio. The milling operation proceeded at 350 revolutions per minute within an ambient air atmosphere for five continuous hours using a specialized planetary ball mill. Following mechanical blending, the pulverized precursor mixtures underwent high-temperature thermal processing inside a furnace, where they were calcined at 600 degrees Celsius for ten hours at a ramp rate of 3 degrees Celsius per minute. This controlled thermal processing promoted complete crystalline phase formation while yielding stable nanostructured powders ready for comprehensive physicochemical characterization and subsequent thin-film photoanode deposition.
Fabrication of the operational photovoltaic cells involved dispersing 30 milligrams of each calcined perovskite powder into 0.1 milliliters of absolute ethanol, followed by fifteen minutes of ultrasonic water bath agitation to generate a homogeneous, viscous slurry. Technicians deposited the resulting perovskite paste onto indium tin oxide coated glass substrates utilizing the standard doctor-blade spreading technique. The coated glass photoanodes were thermally annealed at 300 degrees Celsius for twenty minutes to secure robust mechanical adhesion before undergoing dye sensitization with 140 microliters of a 0.3-millimolar eosin B solution applied via micropipette. The researchers formulated a quasi-solid gel electrolyte by first dissolving lithium iodide, elemental iodine, 4-tert-butylpyridine, 1-methyl-3-propylimidazolium iodide, and guanidinium thiocyanate in acetonitrile, and subsequently blending this liquid matrix with poly(vinyl acetate). Complete sandwich cells were assembled by combining the dye-soaked perovskite photoanode with the polymer gel electrolyte and sealing against an aluminum-coated counter electrode utilizing mechanical binding clips.
Rigorous structural diagnostics demonstrated that altering the B-site transition metal produced unmistakable modifications in the resulting crystallographic geometry and unit cell symmetry. Powder X-ray diffraction patterns analyzed through Rietveld refinement confirmed that both calcined compositions possessed high phase purity and prominent reflection planes matching standard reference databases. However, Rietveld profile modeling revealed that the iron-substituted SSF material crystallized into a tetragonal lattice belonging to the P4mm space group, with refined lattice parameters measuring 3.864 angstroms along the a-axis and 3.853 angstroms along the b-axis. Conversely, the cobalt-substituted SSC compound adopted an undistorted cubic lattice governed by the Pm3m space group with a uniform lattice parameter of 3.840 angstroms. Applying Scherrer crystallite calculations yielded mean crystallite dimensions of 26.1 nanometers for SSF and 26.9 nanometers for SSC, while Goldschmidt tolerance factor calculations indicated values of 1.33 and 1.29, respectively, reflecting internal structural distortions generated by transition metal charge differences.
Morphological examinations using field emission scanning electron microscopy and transmission electron microscopy corroborated the formation of uniformly distributed, irregularly shaped nanoparticles across both perovskite varieties. High-resolution transmission micrographs and selected area electron diffraction ring patterns verified well-defined crystallographic planes indexing directly to the (110), (111), (200), (211), and (220) orientations identified during X-ray diffraction. Statistical particle size counting established mean grain dimensions of 26.3 nanometers for the iron-based SSF nanoparticles and 26.6 nanometers for the cobalt-based SSC structures. Complementary energy dispersive X-ray spectroscopy confirmed the stoichiometric presence and homogeneous spatial distribution of strontium, samarium, oxygen, and the respective iron or cobalt cations throughout the synthesized powders. Microstructural uniformity confirmed that the mechanical milling process combined with controlled thermal calcination yielded high-quality nanosized oxide powders without significant secondary phase segregation.
Vibrational spectroscopy further illuminated the local chemical bonding environments and metal-oxygen coordination configurations within the calcined perovskite matrices. Raman spectra obtained from the iron-containing SSF samples exhibited a pronounced scattering band centered at 500 inverse centimeters, corresponding to iron-oxygen vibrational stretching at tetrahedral crystallographic sites, accompanied by distinct modes at 470 and 340 inverse centimeters associated with parallel and crossed polarizations. The cobalt-bearing SSC samples displayed an analogous Raman-active band located near 490 inverse centimeters, reflecting cobalt-oxygen bonding geometries. Parallel Fourier transform infrared spectroscopy confirmed these coordination characteristics, exhibiting clear iron-oxygen stretching at 510 inverse centimeters and intermediate oxygen-iron-oxygen vibrations at 659 inverse centimeters in SSF, alongside octahedral cobalt-oxygen vibrations at 426 inverse centimeters and bridging cobalt-oxygen-cobalt modes at 570 inverse centimeters in SSC. Both compositions exhibited broad infrared features at 854 inverse centimeters ascribed to metal-oxygen interactions, alongside hydroxyl absorption bands near 1450 inverse centimeters.
Nitrogen gas adsorption-desorption isotherms measured at cryogenic temperatures revealed critical differences in the textural surface architecture and porosity of the two perovskite compositions. Both materials exhibited classic type-IV hysteresis loops that verify the presence of an intrinsically mesoporous framework. Brunauer-Emmett-Teller calculations showed that the iron-modified SSF material developed a specific surface area of 52.6 square meters per gram, accompanied by an average pore diameter of 1.24 nanometers and a cumulative pore volume of 0.202 cubic centimeters per gram. In comparison, the cobalt-modified SSC material yielded a lower specific surface area of 35.8 square meters per gram, wider average pore diameters of 1.68 nanometers, and a total pore volume of 0.198 cubic centimeters per gram. The substantially greater specific surface area and finer pore distribution exhibited by SSF provide vastly expanded physical contact areas, which dramatically enhance dye chemisorption density and augment overall photon harvesting capacity across the operating photoanode surface.
Optical characterization conducted via ultraviolet-visible absorption spectrophotometry highlighted fundamental variances in electronic band structure directly attributable to B-site transition metal selection. While cobalt-substituted SSC demonstrated strong optical absorption confined primarily to deep ultraviolet wavelengths between 200 and 330 nanometers, iron-substituted SSF exhibited extended absorption across the 200 to 350 nanometer window along with noticeable visible light harvesting extending through 380 to 450 nanometers. Direct energy bandgaps extrapolated using Tauc functional plots revealed that SSF possesses an optical bandgap of 2.4 electron volts, whereas SSC exhibits a considerably wider bandgap of 3.6 electron volts. This pronounced narrowing in bandgap energy stems from the differing electronegativity between iron, cobalt, and surrounding oxygen anions. Steady-state photoluminescence emission spectra recorded between 680 and 730 nanometers confirmed substantial signal quenching in SSF, providing direct physical evidence of suppressed electron-hole radiative recombination and swifter photoinduced charge transport.
Solid-state electronic transport assessments performed through four-point probe and Hall effect measurements demonstrated that B-site iron substitution imparted superior electrical properties. Hall coefficient measurements confirmed n-type majority carrier conduction dominated by electrons in both perovskite matrices. However, the iron-substituted SSF semiconductor exhibited an electrical conductivity of 4.98 siemens per centimeter and an electrical resistivity of 0.201 ohm centimeters, outperforming the cobalt-based SSC material, which registered a lower conductivity of 2.31 siemens per centimeter and a higher resistivity of 0.432 ohm centimeters. Furthermore, the electron carrier mobility in SSF reached 5.598 square centimeters per volt-second, more than doubling the 2.482 square centimeters per volt-second recorded for SSC. Electrochemical cyclic voltammetry conducted between negative 0.4 and positive 0.6 volts in potassium hydroxide electrolyte further demonstrated reversible redox capacitive behavior, with SSF exhibiting larger current response envelopes that confirm rapid interfacial charge movement across the semiconductor interface.
Electrochemical impedance spectroscopy corroborated these electronic findings by quantifying charge transfer kinetics across the photoanode, dye, and electrolyte junction. In the resulting Nyquist plots, high-frequency semicircular arcs representing charge-transfer resistance were modeled against equivalent electrical circuits. The analysis proved that the iron-functionalized SSF photoanode exhibited a low charge-transfer resistance of just 12.18 ohms, whereas the cobalt-functionalized SSC electrode exhibited a much larger resistance of 28.24 ohms. The diminished resistance observed in SSF reflects optimized electrical contact at the semiconductor-electrolyte interface, which prevents stagnant carrier pooling and mitigates destructive parasitic back-reactions. Concurrently, the lower charge-transfer resistance combined with elevated specific surface area facilitates unhindered ionic diffusion and accelerated carrier injection, directly mirroring the reduced charge recombination initially identified during optical photoluminescence quenching measurements.
Photovoltaic parameter evaluations carried out under standardized AM 1.5G simulated solar illumination at 100 milliwatts per square centimeter active intensity confirmed the dramatic macroscopic performance benefits of iron substitution. Current density-voltage curves documented that both perovskite photoanodes sustained an identical open-circuit voltage of 0.61 volts, notably exceeding the 0.49 volts recorded for baseline titanium dioxide devices. However, the short-circuit current density of the iron-based SSF cell surged to 13.33 milliamperes per square centimeter, whereas the cobalt-based SSC device produced only 4.73 milliamperes per square centimeter. This sharp threefold divergence in photocurrent generation aligns directly with the superior eosin B dye loading enabled by SSF’s enlarged surface area, combined with broader visible photon capture and unhindered electron transport. Furthermore, electron hopping facilitated by mixed iron valences between trivalent and tetravalent states likely accelerates internal conduction, enabling SSF to achieve its peak 6.24 percent power conversion efficiency.
Subject of Research: Photovoltaic performance enhancement of dye-sensitized solar cells using iron- and cobalt-doped perovskite photoanodes
Article Title: Enhancing dye-sensitized solar cell performance by introducing Fe/Co into the B-site of Sr0.7Sm0.3BO2.89 perovskite photoanodes
Article References: Ndlovu, S., Muchuweni, E., & Nyamori, V. O. (2026). Enhancing dye-sensitized solar cell performance by introducing Fe/Co into the B-site of Sr0.7Sm0.3BO2.89 perovskite photoanodes. Materials for Renewable and Sustainable Energy, 15(1), Article 23. https://doi.org/10.1007/s40243-026-00366-6
Image Credits: AI Generated
DOI: 10.1007/s40243-026-00366-6
Keywords: dye-sensitized solar cells, perovskite photoanodes, power conversion efficiency, energy band gap, electrical conductivity, charge carrier mobility, electrochemical impedance spectroscopy, charge transfer resistance, ball milling synthesis, Rietveld refinement, photoluminescence quenching, eosin B dye, Brunauer-Emmett-Teller surface area, short-circuit current density, open-circuit voltage, transition metal substitution
News Source: Denise Maddox. (November 21, 2026). Iron Substitution in Perovskite Photoanodes Boosts Dye-Sensitized Solar Cell Efficiency. Scienmag.
We bring you the latest biotechnology news from best research centers and universities around the world. Check our website.
Enter your email address to subscribe to this blog and receive notifications of new posts by email.


Bioengineer.org © Copyright 2023 All Rights Reserved.
Login to your account below




Please enter your username or email address to reset your password.


Bioengineer.org © Copyright 2023 All Rights Reserved.

source

This entry was posted in Renewables. Bookmark the permalink.

Leave a Reply