Thank you for visiting nature.com. You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.
Advertisement
Scientific Reports volume 16, Article number: 3871 (2026)
The present study investigates the performance enhancement of photovoltaic–thermal (PVT) systems using a comparison of conventional water coolant and Al2O3–water nanofluid coolant. Outdoor experiments were conducted in Pune, Maharashtra, India, by varying Al2O3 nanoparticle concentrations in a spiral copper thermal absorber integrated with a polycrystalline PV module. The objective was to evaluate how coolant type and nanoparticle loading influence overall PVT system efficiency with practical feasibility. The study uniquely combines thermal, electrical, hydraulic considerations to identify the realistic applicability of Al2O3 nanofluid cooling in PVT systems with spiral thermal absorber. This holistic approach provides practical insights for optimizing PVT performance in domestic and industrial applications under Indian climate conditions—representing a significant advancement over existing studies. The higher thermal conductivity of the Al2O3 nanofluid facilitated more effective heat extraction from the PV surface, resulting in reduced operating temperature, improved electrical output, and enhanced thermal energy recovery. Al2O3 water-nanofluids proved particularly effective, enhancing thermal conductivity and facilitating heat recovery of 5–12 °C. Improvements were observed in thermal efficiency (57.51%), electrical efficiency (9.8%), overall efficiency (67.31%), and energy-saving potential (30.66%). For the water-cooled PVT system, a Reynolds number of 1717.6 was recorded, which decreased by 11.67% to 1517 at the highest nanofluid concentration. The friction factor increased from 0.0906 (water cooling) to 0.0966 with 5% Al2O3 nanofluid, while the pressure drop rose from 521.0 to 829.6 Pa. Although performance improves with increasing nanoparticle concentration, the accompanying rise in viscosity, friction losses, and preparation cost leads to higher pressure drop and pumping requirements.
The word sustainability is continuously in the news and print media, ensuring the long-term health of the economy, environment, and society. Sustainability1 focuses on resources that maintain a healthy planet and a stable future. In the context of energy2, sustainability refers to fulfilling energy demand without compromising future energy generation in a healthier way. Sustainable energy harvesting plays a vital role in progressing toward United Nations energy goals351,52,53. It triggered the energy sector to shift toward renewable energy sources54. The research community is continuously striving to identify newer technology that extracts maximum useful energy in a sustainable manner. The wind, tidal, hydro, and solar are leading renewable sources, but solar energy has dominated for the last two decades in renewable power generation4. This dominance is due to the use of a solar PV system that converts incident solar radiation into electricity through the Photovoltaic (PV) effect5.
According to Solar-Power Europe6, installation of solar power PV technology reached 597 GW in 2024, which is 33% more compared to 2023. 70% of new installations were observed in the Asia–Pacific region and dominated global renewable energy expansion. The power generation of PV observed a decline at higher radiation levels due to the carrying capacity at elevated PV surface temperature7. This negative effect restricts the use of the PV system and can be eliminated by incorporating a cooling arrangement that reduces PV surface temperature. The multiple techniques, such as water cooling, Air cooling, refrigerant cooling, PCM cooling, and nanofluid cooling, were observed in the literature8 to control PV surface temperature. The air and water are conventional cooling media and preferred over other coolants due to ease of availability, low cost, and stability. Studies9,10 were conducted with water coolant to lower PV surface temperature and proved to be an effective coolant. The water is favored over air due to its better thermal conductivity. Nanofluids, a revolutionary blend of base fluids and nanoparticles, have emerged as a game-changer in thermal management, exhibiting significantly enhanced thermal conductivity that is transforming industries and applications11, the application of nanofluid for heat transfer enhancement has been rigorously studied and preferred for PV cooling. The study12 compared Air-natural, Air forced, water, SiO2 + water, and Fe3O4 + water coolant for PVT application. The comparative study among the above coolants concluded that the PVT with SiO2/water resulted in 54.29% highest power and 3.35% electrical efficiency improvements compared to natural PV cooling.
This research13 evaluates the PVT with carbon nanotube (CNT) nanofluid coolant in Dhaka, Bangladesh. A numerical simulation, employing the Galerkin weighted residual-based finite element method, analyzes the effects of Reynolds number ranging from 200 to 1000, 200 W/m2 to 1000 W/m2 radiation on system efficiency. Results show that an increased Reynolds number lowers PV surface and fluid outlet temperatures and improves overall efficiency, while increased solar irradiation has the opposite effect of increasing surface temperature, thereby reducing efficiency. This experimental study14 investigates the energy-exergy performance of a PVT incorporating a serpentine tube thermal absorber and magnetite nano-additives. Results show that combining a sinusoidal serpentine tube and nanofluid improves both efficiency of a PVT with water, Cu + water, and Al2O3 + water as coolants. Results endorsed the use of Cu + water nanofluid due to significantly improved PVT performance compared to other coolants. It was also revealed that tube diameter had a negligible effect, while tube length significantly enhanced thermo-electrical performance.
This study15 evaluates the performance of PVT with water, CuO-water, and Al2O3-water mathematically and validated with experimental work. The CuO-water coolant exhibited the highest overall efficiency of 51.22% and energy accumulation efficiency of 72.58%, representing a significant improvement compared to using water and Al2O3 + water. The experimental study16 investigates the performance of a PVT system using a serpentine tube collector and a hybrid nanofluid composed of water, Fe3O4, and SiO2 nanoparticles at a 3wt% and 20–40 LPM. Results show that the proposed nanofluid significantly improves the system’s performance. At 40 LPM, the hybrid nanofluid achieved combine efficiency of 67%. The experimental study17 investigated PVT with Al2O3 + water coolant with concentrations ranging from 0.05 to 0.5 wt%. The best performance was observed with 0.5 wt% nanofluid, 126.71% increment in thermal, and 7.38% increment in electrical performance when equated to pure water. The flat-plate hybrid collector with pure water and water-based Al2O3 nanofluid was examined18 at a volume concentration of 0.1% of Al2O3 nanoparticles, and a flow rate ranging from 0.5 to 2.0 LPM. It was observed that the utilization of water-based Al2O3 nanofluids in hybrid collectors presents a promising avenue for enhancing thermal performance and efficiency. While significant advancements have been made, ongoing research is essential to address the challenges of pressure drops and aggregation effects. Application of Al2O3 for PVT cooling19 at outdoor Iranian climatic conditions was studied. It was observed that Al2O3 was found beneficial in terms of an increase in electrical and thermal efficiency. The combine overall efficiency increased was 18% while thermal efficiency enhancement at 1.5 g nanofluid was 27%. The electrical efficiency was increased nanofluid11% and 14% with 1.5 g of nanofluid. The study20 demonstrated that Al2O3 nanofluid can improve panel efficiency of the PVT system. CFD approach using ANSYS R18.2 was preferred to simulate a photovoltaic panel under steady-state temperature. Simulations are performed to define temperature changes in the PV solar panel and collectors. It was observed that the PVT system showed the highest electrical efficiency, reaching 11.92% and thermal efficiency of 50.75%. The simulation concluded that to maintain the PVT performance, the absorber material must have high heat transfer abilities.
The cooling performance of a hybrid photovoltaic/thermal (PV/T) system using metal oxide nanofluids, specifically CuO and Fe2O3, at various volume fractions was studied21. The study showed that using CuO and Fe2O3 nanofluids significantly enhanced the cooling efficiency of the PV cells, reducing their temperature by 23.49% and 34.58% respectively at a volume fraction of 0.3%. This cooling improved the overall energy and exergy efficiencies of the system. The electrical efficiency of the PV/T system increased by 9.21% and 10.30% for cooling with CuO and Fe2O3, respectively, compared to the uncooled system. Additionally, thermal efficiency improved by about 38.9% and 43.3% under similar conditions. The cooling performance of a hybrid photovoltaic/thermal system using CuO and Fe2O3 nanofluids was investigated22. It was observed that hybrid nanofluids demonstrated improved efficiency and heat transfer capabilities, but shown increased pressure drops. Employing a TiO2–Fe2O3 hybrid nanofluid at a 0.3% concentration resulted in a 13% increase in electrical efficiency and a 44% increase in thermal efficiency compared to using a Fe2O3-based nanofluid alone.
The performance of a photovoltaic (PV) system may be increased by lowering the operating temperature. The photovoltaic electrical efficiency will drop when the surface temperature rises, which will also have an adverse effect on the panel’s performance and lifespan. Among the studied nanoparticles in literature, Al2O3 (aluminium oxide) nanoparticles are favoured in various cooling applications due to their exceptional properties like high strength, large surface area, and chemical stability. In particular, Al2O3 + water offers a combination of advantages such as high thermal conductivity, good chemical stability, wide availability, and cost-effectiveness that make Al2O3 + water a strong contender for various heat transfer applications compared to other types of nanoparticles. The literature studies show promising results with nanofluids containing Al2O3 for improving heat dissipation and PV efficiency. While literature shows promising results in enhancing heat transfer and improving PV performance with nanofluids, more work is needed to validate these findings across diverse operating conditions and to develop practical, real-world applications. In the literature, different nanoparticles, base fluids, and concentrations were preferred, but the Al2O3 + water + copper spiral thermal absorber configuration for PV cooling for the northern region of India is very limited. This study aims to provides detailed, experimentally validated insight into how increasing nanoparticle concentration (1–5%) influences PV surface temperature reduction, electrical power generation, thermal energy recovery, overall system efficiency. Similarly The study intend to provides new knowledge on how Al2O3 nanofluid affects fluid dynamics inside a PVT system by establishing direct correlations between concentration and Reynolds number drop, friction factor increase, pressure drop rise. These insights are essential for selecting pumps, reducing energy losses, and designing efficient fluid circuits. This study proposed an outdoor experimental investigation utilizing a spiral circular copper-based thermal absorber pasted on the flipside of PV to dissipate heat at varying concentrations of nanoparticles. The experimental investigation aims to reveal a significant impact of the spiral thermal absorber with nanofluid cooling, particularly in relation to its operating temperature and subsequent electrical and thermal output.
It has been observed that no previous work experimentally evaluates this spiral copper thermal absorber with Al2O3–water nanofluid for PVT configuration in a real outdoor environment in India, making this setup and testing approach novel. It is also seen that the most existing studies use ≤ 2% concentrations of nanoparticles. This work systematically investigates five concentrations, providing deeper insight into how nanoparticle loading influences heat transfer, electrical efficiency, and hydraulic behaviour and also compare the performance with water cooling and non-cooled PV system. Unlike typical studies focusing only on thermal/electrical gains, this work uniquely analyzes Simultaneous thermo-electrical and hydraulic evaluation, revealing performance–penalty interactions incorporating reduction in Reynolds number, increase in friction factor, pressure drop escalation, alongside efficiency improvement, providing a realistic operational perspective. This research delivers real-world insights on how thermal absorber geometry, nanofluid concentration, and hydraulic behavior interact in a PVT system.
The experimental setup shown in Fig. 1 consists of a PV and PVT system designed to evaluate the electrical and thermal performance of the module under controlled conditions. The setup includes a polycrystalline photovoltaic panel (rated power: 100 Wp) integrated with a spiral circular thermal collector for heat recovery. A standard polycrystalline PV panels with dimensions 1.010 m × 0.665 m and nominal efficiency of 14.9% were used for experimental work. The PVT unit was mounted at a fixed tilt angle of 3° corresponding to the site’s latitude to maximize solar incidence. Electrical measurements are recorded using a digital multimeter and has error of 0.5 %. A spiral thermal absorber of 0.027 m diameter and 5.63 m length was attached at the rear side of the PV module. The pictorial view of thermal absorber is shown in Fig 2a while cut-section of PVT system is shown in b). The manufactured PVT system and thermal absorber specifications are discussed in Table 1. The coolant is circulated using a centrifugal pump of 0.25 hp with a controlled flow rate. Solar irradiance measured using a thermopile type pyranometer with accuracy: ± 2% and kept parallel to PV panel. An Ambient temperature and PV surface temperature measured using calibrated thermocouples (Type-K, uncertainty: ± 0.5 °C). Water inlet and outlet temperatures measured with digital thermometers (uncertainty: ± 0.3 °C). The Voltage and current measured with a digital multimeter (accuracy: ± 0.5%). All parameters are continuously recorded at 30-minute intervals from 10:00 to 16:00 h. all instruments used for noting observations are calibrated with reference standards.
Outdoor experimental setup.
(a) Flipside of thermal absorber (b) Cross section of PVT system.
The Al2O3 (aluminum oxide) nanoparticles used in the current study was purchased from Sigma-Aldrich Pvt. Ltd., India and sample is shown in Fig. 3. The nanoparticles were of analytical grade and supplied in dry powder form from manufacturer. According to the supplier’s specifications, the Al2O3 nanoparticles had 99.8% purity, a specific surface area of approximately 40–50 m2/g. The particles were white in color and exhibited high thermal stability, making them suitable for nanofluid preparation. The stability of the Al2O3–water/nanofluid was assessed through a visual sedimentation analysis. After preparation, the nanofluid samples were poured into transparent glass vials, sealed, and left undisturbed at room temperature to observe any settling behavior. The samples were monitored at regular time intervals—1 h, 6 h, 24 h, 48 h, and 72 h. Throughout the observation period, no visible sedimentation or formation of large aggregates was detected at the bottom of the containers, indicating that the particles remained uniformly suspended in the base fluid. The absence of phase separation or color variation further confirmed the stability of the nanofluid. The prepared samples of Al2O3 + Water nanofluid at various concentrations are in Fig. 4.
sample of Al2O3 nanopowder.
Prepared samples of Al2O3 Water nanofluid.
The surface morphology of copper oxide found in (Fig. 5a, b) depicts a flakes size varying from 120 to 159 nm which could be a sign of crystal growth and densification. This assembles morphology could contribute towards energy conservation opportunities and while underscoring its pivotal role in nanofluid applications. The magnetic stirrer with hot plate was used for stability test and set up is shown in Fig. 5c.
(a) Scanning electron microscope of Al2O3 (b) EDS pattern of Al2O3 nanoparticles (c) Magnetic stirrer with hot plate for stability test.
The density, specific heat and thermal conductivity of Al2O3 water nanofluid were calculated using expression below. The thermophysical properties of Al2O3 nanoparticles and base Water fluid are tabulated in Table 2 and derived properties of Al2O3 + water nanofluid from Eqs. (1), (2), (3), and (4) are shown in Table 3.
Density of nanofluid23:
Specific heat24:
Thermal conductivity25:
A PVT system works on principle of simultaneous generation of thermo-electrical power. The incident solar radiations fall on the surface of PV panel and part of it is converted into electrical power (PElec) by photovoltaic effect as discussed in introduction and rest is converted into heat. The electrical power is product of voltage and current. Based on the electrical power, the electrical efficiency from PVT system is calculated as10
Thermal efficiency obtained from coolant is assessed as follows,
The total efficiency from PVT system is calculated as sum of thermal efficiency and electrical efficiency while equivalent energy saving efficiency is calculated by using fitment factor of 0.3828.
To calculate Reynolds number,
The friction coefficient is crucial in determining the amount of energy lost due to friction. A higher coefficient of friction leads to greater frictional resistance and consequently, more energy loss in a system. This energy loss can manifest as heat, wear, and reduced efficiency hence the friction coefficient (Cf) is evaluated as29
the pressure drop is expressed as30,
Uncertainty analysis is essential for ensuring the reliability and accuracy of experimental results. In this study, the overall uncertainty was determined using the Kline and McClintock method, which is widely adopted in experimental heat transfer and thermal system investigations due to its robustness in handling multiple measured variables and propagation of errors30
The aforementioned general equation was applied to determine the uncertainties in electrical and thermal performance.
For Thermal efficiency
For Electrical efficiency
where, R= {m, Tout, Tin, Ac, v, Voc, Ig} are the average value of parameters
Hence, by applying above equation uncertainty in the thermal and electrical performance is calculated
Photovoltaic (PV) modules face a significant challenge in maintaining efficiency due to rising operating PV temperatures, especially during peak solar irradiance. To address this, an innovative Al2O3-water cooling system was designed and experimentally tested at Kamshet, Pune, India (18.7663° N, 73.5554° E). This study showcases the impact of a backside cooling system with varying Al2O3 concentrations and constant flow rates on PV panel performance. By meticulously analyzing temperature, power output, solar radiation, and water temperatures, this research aims to demonstrate the cooling system’s effectiveness in enhancing electrical and thermal efficiency. The findings not only underscore the benefits of this approach but also provide valuable insights into its limitations, setting a benchmark for future innovations in PV panel cooling technologies.
Solar radiation’s dynamic nature is shaped by geographic, and atmospheric factors, leading to significant variations in incident radiation. The studied outdoor experimentation captures this variability and presented in Fig. 6 that showcased half-hourly fluctuations in solar radiation. the solar energy has three key components: beam radiation (direct sunlight without scattering), diffuse radiation (scattered sunlight), and global radiation (the sum of global and diffused radiations).
Variation of Solar radiation incident on PV/PVT system.
As shown in Fig. 6, global and beam radiations followed flattened U shape structure and similar structure is observed in the literature10. Our experiment tracked global radiation’s diurnal pattern, starting at 669 W/m2 at 10:00 h, peaking at 960.8 W/m2 at solar noon (12:30 h), and declining to 680 W/m2 by the end of the day period. The average global radiation throughout the day was 697.01 W/m2. Meanwhile, diffuse radiation fluctuated between 102 and 125 W/m2, highlighting the dynamic interplay between direct and scattered solar radiation.
As discussed in introduction, PV panels harness solar radiation and a significant portion is converted into electricity, while excess energy is transformed into heat, compromising panel efficiency. Understanding the intricate relationship between radiation and temperature is key to optimizing PV system design and operation. the proposed PV cooling system tackles this challenge by leveraging heat conduction from the PV panel to a spiral thermal absorber, followed by convection to a flowing coolant, effectively dissipating excess heat and regulating panel temperature.
The experimental measurements revealed a significant variation in surface temperature between the standalone PV module and the PVT with water and nanofluid under identical operating conditions. Figure 7 illustrates the temporal variation of surface temperature for both systems during a typical sunny day.
Effect of different cooling methods on PV surface temperature.
The temperature decreases in the PVT system when Al2O3 nanofluid circulates because the nanoparticles significantly enhance the fluid’s thermal conductivity, allowing heat to be conducted away from the PV layers more quickly than with water alone. The suspended nanoparticles also increase the convective heat transfer coefficient by disturbing the thermal boundary layer and improving energy exchange at the absorber–fluid interface. As a result, heat is removed more efficiently from the glass, EVA, cell, and backsheet layers, reducing the PV operating temperature and improving electrical performance.
While the non-cooled PV module soared to a highest temperature of 61.1 °C at 12:30 h, just after solar noon, the PVT module’s water-cooling system kept temperatures at a relatively cooler 56.8 °C under identical irradiance and ambient conditions, showcasing the effectiveness of thermal management in enhancing PV performance. This reduction of approximately 4.3 °C in the PVT module is attributed to the active heat removal through the circulating working water fluid. The average temperature of non-cooled PV was 55.03 °C, while it was reduced to 50.76 °C by water cooling.
Incorporating 1% Al2O3 nanoparticles into water further reduced the average PV surface temperature to 48.45 °C. A similar trend of temperature reduction with nanoparticle addition has also been reported in previous studies. The findings revealed a striking trend: as nanoparticle concentration increases, PV surface temperature plummets, underscoring the potent cooling potential of nanofluids in photovoltaic applications. At 2% concentration, the average PV surface temperature dropped to 47.02 °C, whereas at 3%, 4% and 5%, the average surface temperatures were further reduced to 46.00 °C, 44.82 °C, and 43.77 °C, respectively. This reduction can be attributed to the enhanced thermal conductivity and heat transfer coefficient of the nanofluid, which facilitates more effective heat removal from the PV surface.
The outlet water temperature is a vital metric for evaluating PVT system performance, influenced by cooling technique and working fluid. Figure 8 highlights the impact of Al2O3 nanofluids on outlet temperature, showcasing notable deviations from conventional water cooling. Water’s moderate thermal conductivity (~ 0.6 W/mK) provides a solid foundation, but the addition of Al2O3 nanoparticles unlocks enhanced thermal conductivity, amplifying convective heat transfer coefficient and resulting in higher outlet temperatures.
water inlet–outlet temperature study for different cooling methods.
In thermal systems such as PVT collectors, increasing convective heat transfer coefficient enhances the movement of heat from the absorber plate into the fluid. When the fluid has higher thermal conductivity—such as nanofluids containing Al2O3 nanoparticles—it also improves conduction inside the fluid by allowing heat to spread more rapidly through the medium. Thus, a higher heat transfer coefficient combined with enhanced fluid conductivity leads to more efficient heat dissipation, better surface cooling, and improved overall thermal performance of the system. This synergy between nanoparticles and fluid enables more efficient energy absorption from the PV surface, driving up outlet temperatures and underscoring the potential of nanofluids in PVT systems.
Notable temperature boosts were observed with Al2O3 nanofluids: a 1% concentration yielded a 3.96% increase in outlet temperature (39.61 °C) compared to water cooling (38.1 °C). Stepping up to 2% concentration, the outlet temperature rose by 8.26% to 41.25 °C. The most significant jump came with 5% Al2O3, reaching 46.52 °C—a substantial 22.09% increase, underscoring the impact of nanoparticle concentration on thermal performance.
The crystalline silicon PV cells have a negative temperature coefficient about ~ − 0.4% to − 0.5% per °C above 25 °C8 hence the elevated temperature reduces electrical power output significantly. The lower average electrical power of 36.5 W was noted for non- cooled PV system as shown in Fig. 9. In the absence of nanoparticles i. e. PVT with water, the cooling effect is minimal, leading to a relatively high PV surface temperature. In the case of PVT with water, the average electrical power was 39.1 W. This relatively low power compared to PVT with Al2O3 water nanofluid, due to the higher average PV surface temperature (50.76 °C), which negatively impacts PV performance because of the temperature coefficient of the cell.
Variation of electrical power at various concentrations.
When a nanofluid with 1% Al2O3 was employed, the electrical power output increased to 40.3 W, corresponding to a 3.06% improvement over PVT with water system. At 2%, the cooling effect became more significant, lowering the average PV surface temperature by approximately 7–8 °C, and the electrical power increased to 41.6 W (6.39% improvement). The highest tested concentration, 5%, yielded an electrical power output of 44.5 W, which represented a 13.81% improvement compared to the PVT with water system.
The electrical efficiency of a photovoltaic (PV) module is highly sensitive to its operating temperature, which is influenced by the cooling technique employed in a photovoltaic-thermal (PVT) system. Non-cooled, water-cooled, and Al2O3 water-based cooling methods were studied with varying concentrations, providing varying levels of heat removal, leading to distinct electrical performance trends.
From Fig. 10, in the Case of a non-cooled PV system, the average PV surface temperature reached 55.03 °C, resulting in an electrical efficiency of 5.90%, significantly lower than the STC rating (14.9%) due to the high operating temperature. With water-cooled PVT, the average PV temperature reduced to 50.76 °C, increasing efficiency to 6.7%, representing an improvement of 13.55% over the non-cooled PV system31.
Electrical efficiency variation with cooling methods.
The Al2O3-based nanofluid PVT system provided the most effective cooling, maintaining the PV temperature at 48.45 °C at 1% concentration, which resulted in the electrical efficiency of 7.11%, corresponding to a 20.50% improvement over the non-cooled PV system. The lowest surface temperature of 43.77 °C was observed at 5% concentration, which resulted in the highest electrical efficiency of 8.80%, corresponding to a 49.15% improvement over the non-cooled PV system. The electrical efficiency at 2%, 3% and 4% concentrations was 7.65%, 8.00% and 8.39% respectively.
Thermal efficiency in PVT systems is a key indicator of solar heat utilization, heavily influenced by the cooling medium’s thermal conductivity. From Fig. 11, Water-based cooling yielded an average thermal efficiency of 38.8%, but introducing Al2O3 nanoparticles significantly boosted performance. A 1% concentration resulted in a 17.86% increase in thermal efficiency (45.73%). Further increments in nanoparticle concentration led to substantial gains: 28.06% at 2% (49.69%), 34.09% at 3% (52.02%), and 41.88% at 4% (55.05%). Notably, the efficiency growth slowed beyond 2% concentration, likely due to increased viscosity and sedimentation. The peak average thermal efficiency of 57.51% was achieved at 5% Al2O3, representing a 48.22% enhancement over water cooling and a 3.28% increase from 4% Al2O3.
Variation in thermal efficiency for different cooling methods.
The PV/PVT system performance was assessed based on energy and energy-saving efficiencies, determined by the utilization of solar energy through electrical and thermal outputs. Energy-saving efficiency was calculated using an equivalent energy conversion factor of 0.38. The assessment was performed to determine the optimal coolant type and concentration32,33,34.
As Fig. 12 illustrates, Al2O3 nanoparticles significantly boost thermal conductivity, enabling superior heat transfer and rapid PV surface cooling, thereby reducing operating temperatures and enhancing overall efficiency. The sweet spot was achieved at 5 wt% nanofluid concentration, yielding a maximum average overall efficiency of 66.32%—a stark contrast to the 38.85% recorded with water-cooled PVT. Energy-saving efficiency followed suit, with nanofluids outperforming water cooling, reaching 30.66% at 5% concentration versus 21.46% with water. In contrast, the uncooled PV system s electrical efficiency was limited to 5.90%.
Overall and energy-saving efficiencies of PV/PVT systems under different cooling methods.
The uncertainty analysis was conducted using the Kline and McClintock method to ensure the reliability of the experimental results. The calculated uncertainties were 0.87% for thermal efficiency and 1.98% for electrical efficiency, indicating a high level of confidence in the measured performance parameters.
The experimental study showed that water-cooled PVT systems boast the highest Reynold number of 1717.6, but adding Al2O3 nanoparticles causes a decline. As shown in Fig. 13, a 1% concentration yields a 2.4% Re drop, while 5% concentration results in an 11.11% decrease. As Reynold number decline, the flow transitions to laminar, fostering a thicker thermal boundary layer that enhances heat transfer that a crucial factor in optimizing PVT performance35,36,37,38.
Variation in Reynolds number at various nanoparticle concentration levels.
In the experiments, the Reynolds number for the water-cooled PVT system was Re = 1717.6, which decreased to Re = 1517 at the highest nanofluid concentration. These values fall well within the laminar flow regime (Re < 2300) for internal flow in circular tubes. Therefore, all observed variations in friction factor and pressure drop correspond to laminar flow behavior, where viscosity-driven effects dominate46,47,48.
As the nanoparticle concentration increases, both the dynamic viscosity (μ) and density (ρ) of the fluid rise49,50,51, which reduces the Reynolds number but increases the friction factor and pressure drop. Because the flow remains laminar throughout the study, the increase in pressure drop is primarily attributed to the viscosity increase rather than turbulence effects. This reinforces the physical consistency of the current research findings.
In PVT systems, the friction coefficient plays a pivotal role in fluid dynamics and heat transfer, measuring the resistance to fluid flow caused by wall friction. Nanofluid cooling introduces a trade-off: as nanoparticle concentration increases, viscosity rises, and so does the friction coefficient. Specifically, the friction coefficient jumped by 1.32% to 6.69% as nanoparticle concentration rose from 1 to 5%, compared to the water-based PVT system’s baseline value of 0.0906 shown in Fig. 14
Variation in friction coefficient at various nanoparticle concentration levels.
In PVT cooling systems, the friction coefficient is a key indicator of fluid flow resistance. Adding Al2O3 nanoparticles to water increases viscosity and density, thereby amplifying the friction coefficient. Water, with its low viscosity and density, exhibited the lowest friction coefficient of 0.0906, setting a baseline for comparison with nanofluid configurations.
The addition of Al2O3 nanoparticles to the fluid amplifies both density and dynamic viscosity, leading to increased shear stress and a higher friction coefficient. At 1% Al2O3 concentration, the friction factor measured 0.0918, marking a 1.32% increase from the water-cooled PVT’s baseline of 0.0906. As nanoparticle concentration rises further, the friction factor continues to climb, reaching 0.0966 at 5% Al2O3—a 6.62% increment was noted (Fig. 15).
Variation in pressure drop at various nanoparticle concentration levels.
The experimental results show a clear and monotonic increase in pressure drop as the Al2O3 nanoparticle concentration in the base water is raised from 0 (pure water) to 5% concentration. For the tested PVT loop, the pressure drop increased from 521.0 for pure water to 829.6 Pa at 5% Al2O3, representing a ~ 59.3% rise. This behaviour is consistent with the Darcy–Weisbach relation, where increases in dynamic viscosity (μ) and density (ρ) at higher particle loadings raise the friction factor and reduce Reynolds number, both of which contribute to higher pressure drop.
In present study, the friction factor rose from 0.0906 (water) to 0.0966 (5% Al2O3) while the Reynolds number decreased by about 11.7%, reflecting the competing effects of higher ρ and μ against reduced velocity-driven turbulence. The net result is a substantial hydraulic penalty at higher concentrations that directly impacts pumping power and operational cost. The comparative results of literatures studies based on Al2O3 + water nanofluid and current study are tabulated in Table 4.
This work uniquely analysed five concentrations, providing deeper insight into how Al2O3 nanoparticle loading influences heat transfer, electrical efficiency, and hydraulic behaviour and also compare the performance with water cooling and non-cooled PV system. It sets a new performance benchmark, identifies optimum nanofluid operating thresholds, and provides practical engineering guidelines making it a uniquely valuable contribution to PVT technology development.
The foremost key outcomes are summarised as follows.
Outdoor experimental assessment data show that maximum electrical (9.8%), thermal (57.51%), and energy-saving efficiency (30.66%) was noted for the PVT with 5% Al2O3 nanofluid.
The non-cooled PV system recorded the highest average surface temperature at 50.03 °C, which decreased slightly to 50.76 °C with water cooling and further dropped to 43.77 °C when using a 5% Al2O3 nanofluid.
The PVT system with water achieved average electrical, thermal, and energy-saving efficiencies of 7.66%, 30.20%, and 21.46%, respectively.
The observed improvement in performance is attributed to the combined effect of enhanced thermal conductivity and intensified convective heat transfer, leading to more effective PV cooling and greater overall energy recovery.
Increasing nanoparticle concentration caused a decline in Reynolds number due to higher fluid viscosity. For instance, the Reynolds number decreased from 1717.6 (with water cooling) to 1517 at a 5% nanoparticle concentration.
The coefficient of friction and pressure drop for water-cooled PVT were 0.0906 and 521.0 Pa, respectively. These values increased to 0.0966 and 829.6 Pa when using a 5% Al2O3 nanofluid.The enhanced energy efficiency with nanofluids makes them suitable for hybrid PVT systems; however, nanoparticle loading has operational drawbacks like higher pressure drop, friction factor, and potential sedimentation issues.
While Al2O3 nanofluid outshines water coolant in PVT performance, rising nanoparticle concentrations also hike viscosity, friction, and costs. Future research should prioritize optimizing thermal absorber designs and exploring hybrid nanofluids that balance performance with manageable viscosity and friction to maximizing PVT efficiency.
The datasets used and/or analysed during the current study available from the corresponding author on reasonable request.
Nanofluid density
Nanoparticle density
Base fluid density
Volume concentration of nanoparticles
Specific heat capacity of nanofluid
Specific heat capacity of nanoparticles
Specific heat capacity of base fluid
Thermal conductivity of nanofluid
Thermal conductivity of base fluid
Mass flow rate of water (kg/s)
Specific heat capacity of water (kJ/kg·K)
Temperature change of water (°C)
Area of photovoltaic panel (m2)
Thermal efficiency (%)
Electrical efficiency (%)
Overall efficiency (%)
Energy-saving efficiency (%)
Reynolds number
Coefficient of friction
Velocity of coolant
Weight concentration of nanoparticles
Error
Incident radiation
Photovoltaic thermal system
Scoones, I. Sustainability. Dev. Pract. 17(4–5), 589–596. https://doi.org/10.1080/09614520701469609 (2007).
Article Google Scholar
Rosen, M. A. Energy sustainability with a focus on environmental perspectives. Earth Syst. Environ. 5, 217–230. https://doi.org/10.1007/s41748-021-00217-6 (2021).
Article ADS PubMed PubMed Central Google Scholar
Bexell, M. & Jönsson, K. Responsibility and the United Nations’ sustainable development goals. Forum Develop. Stud. 44(1), 13–29. https://doi.org/10.1080/08039410.2016.1252424 (2016).
Article Google Scholar
Sukhatme SP. Solar energy, principles of thermal collection and storage. 6th Edition. , New Delhi: Tata McGraw Hill Publishing Company Limited; (2012).
Rappaport, P. The photovoltaic effect and its utilization. SolarEnergy 3(4), 8–18. https://doi.org/10.1016/0038-092X(59)90002-7 (1959).
Article ADS CAS Google Scholar
WalburgaHemetsberger, Market outlook for solar power 2024–2028, https://www.solarpowereurope.org/insights/outlooks/eu-market-outlook-for-solar-power-2024-2028/detail#forewordRetrieves on 05/07/2025.
Nasrin, R., Hasanuzzaman, M. & Rahim, N. A. Effect of high irradiation on photovoltaic power and energy. Int. J. Energy Res. 42, 1115–1131. https://doi.org/10.1002/er.3907 (2018).
Article Google Scholar
Satpute, J. B. & Rajan, A. J. Recent advancement in cooling technologies of solar Photovoltaic (PV) system. FME Trans. 46(4), 575–584 (2018).
Article Google Scholar
Satpute, J. et al. Parametric influence and efficiency assessment of water-cooled photovoltaic thermal PV/T absorber designs. Energy 320, 135218. https://doi.org/10.1016/j.energy.2025.135218 (2025).
Article Google Scholar
Satpute, J. et al. Performance assessment of hybrid PV/PVT collectors incorporating natural water-cooling circulation. J. Mines Metals Fuels 72(7), 751–761. https://doi.org/10.18311/jmmf/2024/44945 (2024).
Article Google Scholar
Satpute, J., Campli, S., Alnamasi, K., Alsharif, A. M. & Bashir, M. N. Experimental Investigation of photovoltaic thermal (PVT) system incorporating water-copper oxide nanofluid. Case Stud. Therm. Eng. https://doi.org/10.1016/j.csite.2025.106519 (2025).
Article Google Scholar
Soltani, S., Kasaeian, A., Sarrafha, H. & Wen, D. An experimental investigation of a hybrid photovoltaic/thermoelectric system with nanofluid application. Sol. Energy 155, 1033–1043. https://doi.org/10.1016/j.solener.2017.06.069 (2017).
Article ADS CAS Google Scholar
Azad, A. K., Parvin, S. & Hossain, T. Performance evaluation of nanofluid-based photovoltaic thermal (PVT) system with regression analysis. Heliyon 10(7), e29252. https://doi.org/10.1016/j.heliyon.2024.e29252 (2024).
Article CAS PubMed PubMed Central Google Scholar
Shahsavar, A. Experimental evaluation of energy and exergy performance of a nanofluid-based photovoltaic/thermal system equipped with a sheet-and-sinusoidal serpentine tube collector. J. Clean. Produc. 287, 125064. https://doi.org/10.1016/j.jclepro.2020.125064 (2021).
Article CAS Google Scholar
Mahmood Alsalame, H. A., Lee, J. H. & Lee, G. H. Performance evaluation of a photovoltaic thermal (PVT) system using nanofluids. Energies 14, 301. https://doi.org/10.3390/en14020301 (2021).
Article CAS Google Scholar
Khan, A. A., Danish, M., Rubaiee, S. & Yahya, S. M. Insight into the investigation of Fe3O4/SiO2 nanoparticles suspended aqueous nanofluids in hybrid photovoltaic/thermal system. Clean. Eng. Technol. 11, 100572. https://doi.org/10.1016/j.clet.2022.100572 (2022).
Article Google Scholar
Zamen, M., Kahani, M., Rostami, B. & Bargahi, M. Application of Al2O3/water nanofluid as the coolant in a new design of photovoltaic/thermal system: An experimental study. Energy Sci. Eng. 10, 4273–4285. https://doi.org/10.1002/ese3.1067 (2022).
Article CAS Google Scholar
Srimanickam, B. et al. Experimental studies on water-based Al2O3 nanofluid to enhance the performance of the hybrid collector. J. Nanomater. 2022(1), 9385416. https://doi.org/10.1155/2022/9385416 (2022).
Article CAS Google Scholar
Saadoon, M., Hasan, I. A. & Mohammed, M. J. Preparing nanofluids (Al2O3) for enhancement performance of photovoltaic. Eng. Technol. J. 39(9), 1445–1453. https://doi.org/10.30684/etj.v39i9.2110 (2021).
Article Google Scholar
Arifin, Z., Alfaiz, N.F., Tjahjana, D.D.D.P., Rachmanto, R.A., Prabowo, A.R. and Prasetyo, S.D., 2024, September. Effect of nanofluids Al2O3-Water based collector material on thermal collector photovoltaic performance: Computational fluids dynamics investigation. In AIP Conference Proceedings (Vol. 3124, No. 1, p. 060015). AIP Publishing LLC. https://doi.org/10.1063/5.0227756
Alktranee, M. et al. Experimental and numerical study of a photovoltaic/thermal system cooled by metal oxide nanofluids. Alexandria Eng. J. 94, 55–67. https://doi.org/10.1016/j.aej.2024.03.050 (2024).
Article Google Scholar
Alktranee, M., Al-Yasiri, Q., Mohammed, K. S., Al-Lami, H. & Bencs, P. Energy and exergy assessment of a photovoltaic-thermal (PVT) system cooled by single and hybrid nanofluids. Energy Convers. Manag. X 24, 100769. https://doi.org/10.1016/j.ecmx.2024.100769 (2024).
Article CAS Google Scholar
Ramesh Kumar, R., Karthik, K. & Elumalai, P. V. Enhancing automotive cooling systems: composite fins and nanoparticles analysis in radiators. Sci. Rep. 14, 3650. https://doi.org/10.1038/s41598-024-52141-0 (2024).
Article ADS CAS PubMed PubMed Central Google Scholar
Buongiorno, J. Convective transport in nanofluids. ASME J. Heat Transfer 128(3), 240–250. https://doi.org/10.1115/1.2150834 (2005).
Article Google Scholar
Hamilton, R. L. & Crosser, O. K. Thermal conductivity of heterogeneous two-component systems. J. Ind. Eng. Chem. 1, 187–191 (1962).
CAS Google Scholar
Salem, M. R., Elsayed, M. M., Abd-Elaziz, A. A. & Elshazly, K. M. Performance enhancement of the photovoltaic cells using Al2O3/PCM mixture and/or water cooling-techniques. Renew. Energy 138, 876–890. https://doi.org/10.1016/j.renene.2019.02.032 (2019).
Article CAS Google Scholar
Ramires, M. L. et al. Standard reference data for the thermal conductivity of water. J. Phys. Chem. Reference data 24(3), 1377–1382. https://doi.org/10.1063/1.555963 (1995).
Article ADS CAS Google Scholar
Satpute, J., Campli, S., Alnamasi, K., Alsharif, A. M. & Bashir, M. N. Experimental investigation of photovoltaic thermal (PVT) system incorporating water-copper oxide nanofluid. Case Stud. Therm. Eng. 73, 106519. https://doi.org/10.1016/j.csite.2025.106519 (2025).
Article Google Scholar
Rao, V. T. et al. Thermal analysis of hybrid photovoltaic-thermal water collector modified with latent heat thermal energy storage and two side serpentine absorber design. J. Energy Storage 56, 105968. https://doi.org/10.1016/j.est.2022.105968 (2022).
Article Google Scholar
Kline, S. J., McClintock F. A. Describing uncertain ties in single-sample experiments. Mechanical Engineering, (1953).
Ai, C., Liu, C., Sun, P. & Liu, C. Na2CO3-SiO2-H2O nanofluids synergistically treats coal dust and hydrogen sulfide. J. Environ. Chem. Eng. 13(6), 119365. https://doi.org/10.1016/j.jece.2025.119365 (2025).
Article CAS Google Scholar
Xia, G., He, X., Jia, Y., Zhu, Y. & Tian, Z. Design of a cylindrical thermal rotary concentrator based on transformation thermodynamics. Materials 18(19), 4440. https://doi.org/10.3390/ma18194440 (2025).
Article ADS CAS PubMed PubMed Central Google Scholar
Zhang, Y., Zhang, Y., Zheng, B., Cui, H. & Qi, H. Statistical analysis for estimating the optimized battery capacity for roof-top PV energy system. Renew. Energy 242, 122491. https://doi.org/10.1016/j.renene.2025.122491 (2025).
Article Google Scholar
Wan, A., Peng, S., AL-Bukhaiti, K., Ji, Y. & Ma, S. The early warning method for offshore wind turbine gearbox oil temperature based on FSTAE-ATT. Sustain. Comput. Inform. Sys. 47, 101180. https://doi.org/10.1016/j.suscom.2025.101180 (2025).
Article Google Scholar
Wei, T. et al. City-scale roof-top photovoltaic deployment planning. Appl. Energy 368, 123461. https://doi.org/10.1016/j.apenergy.2024.123461 (2024).
Article Google Scholar
Wang, H. et al. A self-powered wireless temperature sensing system using flexible thermoelectric generators under simulated thermal condition. Measurement 253, 117637. https://doi.org/10.1016/j.measurement.2025.117637 (2025).
Article Google Scholar
Zhang, Y. et al. Design and performance analysis of 15MWth SCO2-cooled micro reactor. Nuc. Eng. Technol. 57(12), 103863. https://doi.org/10.1016/j.net.2025.103863 (2025).
Article CAS Google Scholar
Bi, Y. et al. Design and transient analysis of a novel type passive residual heat removal system. Nuc. Eng. Design 445, 114446. https://doi.org/10.1016/j.nucengdes.2025.114446 (2025).
Article CAS Google Scholar
Saber, R., Abballah, I. M. M., ElSemary, A. A., Altohamy, M. A. & Abdelrahman, A. A. A. Attia OEA, experimental investigation on the effect of using nano fluid (Al2O3 – water) on the performance of PV/T system. Therm. Sci. Eng. Progr. https://doi.org/10.1016/j.tsep.2018.04.016 (2018).
Article Google Scholar
Prasetyo, S. D., ZainalArifin, A. R., Prabowo, E. P. & Budiana,. The impact of cavity in finned thermal collector on PVT performance using Al2O3 nanofluid. Int. J. Thermofluids 27, 101284. https://doi.org/10.1016/j.ijft.2025.101284 (2025).
Article CAS Google Scholar
Ibrahim, A. et al. A comprehensive study for Al2O3 nanofluid cooling effect on the electrical and thermal properties of polycrystalline solar panels in outdoor conditions. Environ SciPollut Res 30, 106838–106859. https://doi.org/10.1007/s11356-023-25928-3 (2023).
Article CAS Google Scholar
Khelifa, A., Attia, M. E. H., Abdelgaied, M., Arıcı, M. & Abdel-Aziz, M. M. 3D numerical analysis of a photovoltaic thermal using bi-fluid: Al2O3–water nanofluid at various concentrations. Int. J. Thermofluids 20, 100523. https://doi.org/10.1016/j.ijft.2023.100523 (2023).
Article CAS Google Scholar
Prasetyo, S. D., Arifin, Z., Prabowo, A. R. & Budiana, E. P. Examining various finned collector geometries in the water/Al2O3 based PV/T system: an analysis using computational fluid dynamics simulation. Int. J. Heat Technol. 42(3), 851–864. https://doi.org/10.18280/ijht.420314 (2024).
Article Google Scholar
Muniyandi, S. & Narayanasamy, S. Experimental analysis on the performance of photovoltaic module with Al2O3 deionized water nanofluid. Therm. Sci. https://doi.org/10.2298/tsci230829268m (2024).
Article Google Scholar
Diwania, S. et al. Modeling and assessment of the thermo-electrical performance of a photovoltaic-thermal (PVT) system using different nanofluids. J Braz. Soc. Mech. Sci. Eng. 43, 190. https://doi.org/10.1007/s40430-021-02909-6 (2021).
Article CAS Google Scholar
Ashish, Kumar Ashish Rajkumar, Devshette Srinidhi, Campli Sanjay Singh, Rathore Pavankumar, Sonawane Ravi, Kumar Amar, Gajbhiye (2025) (2025) Thermal and structural analysis of 304L stainless steel WAAM using finite element analysis Abstract Engineering Research Express 7(3) 035513-10.1088/2631-8695/adebe2
Anuja H., Karle Srinidhi, Campli Masnaji, Nukulwar Vidya, Zinjurde Indira, Dastidar (2025) Experimental Investigation and Optimization of Wollastonite and Tungsten Disulfide Reinforced Epoxy Composites by AHP-TOPSIS Approach Abstract Materials Performance and Characterization 14(1) 119-141 10.1520/MPC20240034
Pavankumar, Sonawane Namdev, Patil Ankita, Avthankar Priyambada, Praharaj Srinidhi, Campli Shaunak, Samudra Tanish, Hire Pranav, Chougule Rahul, Kesale (2025) (2025) Enhancing weld quality and corrosion resistance of C71500 copper nickel alloys through friction stir welding Abstract Engineering Research Express 7(4) 0455d6-10.1088/2631-8695/ae2c47
Ashish, Kumar Campli, Srinidhi Sanjay Singh, Rathore Pavankumar, Sonawane Ravi, Kumar (2025) (2025) Parametric synthesis and RSM-GA integrated optimization of multi-bead deposition in wire arc additive manufacturing of AISI 304L stainless steel Abstract Engineering Research Express 7(3) 035525-10.1088/2631-8695/adf037
Campli, Srinidhi A., Madhusudhan S.V., Channapattana S.V., Gawali Kiran, Aithal (2021) RSM based parameter optimization of CI engine fuelled with nickel oxide dosed Azadirachta indica methyl ester Energy 234121282-10.1016/j.energy.2021.121282
Article CAS Google Scholar
Shylesha V., Channapattana Srinidhi, Campli A., Madhusudhan Srihari, Notla Rachayya, Arkerimath Mukesh Kumar, Tripathi (2023) Energy analysis of DI-CI engine with nickel oxide nanoparticle added azadirachta indica biofuel at different static injection timing based on exergy Energy 267126622-10.1016/j.energy.2023.126622
Article CAS Google Scholar
Jitendra, Satpute Srinidhi, Campli PavanKumar, Sonawane Siddhant, Gade Sunita, Yadav Shylesha, Channapattana Tapobrata, Dey Eustache, Hakizimana (2026) Analysis of ethylene glycol (EG) based nanofluid coolant for enhancing cooling capacity of engine Discover Applied Sciences 8(1) 10.1007/s42452-025-07812-6
C., Srinidhi A., Madhusudhan S. V., Channapattana (2022) Comparative analysis of exhaust gas recirculation and nanoparticles on the performance and emission of diesel engine fuelled with Neem biodiesel blend International Journal of Ambient Energy 43(1) 290-299 10.1080/01430750.2019.1636876
C., Srinidhi A., Madhusudhan S. V., Channapattana (2022) Parametric studies of CI engine at various injection strategies using biodiesel blended nanoparticles as fuel International Journal of Ambient Energy 43(1) 117-127 10.1080/01430750.2019.1630303
Download references
The authors extend their acknowledgement to the financial support of the European Union under the REFRESH-Research Excellence For REgion Sustainability and High-tech Industries project number CZ.10.03.01/00/22_003/0000048 via the Operational Programme Just Transition. This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MSIT) (RS-2022-NR070832) and partly supported by YFL 2025, Yonsei University, Seoul, Korea, .
No funding or grants were received.
Dept of Mechanical Engg, Faculty of Engineering, Suman Ramesh Tulsiani Technical Campus, Pune, 410405, India
Jitendra Satpute & Pravin Thorat
Faculty of Mechanical Engineering, VŠB Technical University of Ostrava, Ostrava, Czech Republic
Jana Petrů & Muhammad Nasir Bashir
Mechanical Department, D Y Patil College of Engineering, Pune, India
Vinod Hiwase
Dept of Mechanical Engg, KLS Vishwanathrao Deshpande Institute of Technology, Haliyal, India
Shylesha Channapattana
Department of Mechanical Engineering, Yonsei University, Seoul, 120-749, Republic of Korea
Muhammad Nasir Bashir & Joon Sang Lee
Dept of Nano Studies and Physics, JSPM Rajarshi Shahu College of Engg, Pune, India
Rupesh Sundge & Sunita Yadav
Faculty of Electrical and Mechanical Engg, College of Military Engg, Pune, India
Srinidhi Campli
Mechanical, JSPM University, Pune, India
Srinidhi Campli
PubMed Google Scholar
PubMed Google Scholar
PubMed Google Scholar
PubMed Google Scholar
PubMed Google Scholar
PubMed Google Scholar
PubMed Google Scholar
PubMed Google Scholar
PubMed Google Scholar
PubMed Google Scholar
Jitendra Satpute(CorrespondingAuthor) : Conceptualization and Experimentation Jana Petrů(Corresponding Author): Project Supervision Srinidhi Campli : Validation Pravin Thorat: Manuscript Drafting Rupesh Sunge: Analysis Vinod Hiwase : Software/Simulation analysis and Drafting of revised manuscript Shylesha Channapattana : Project Administration Muhammad Nasir Bashir: Funding Joon Sang Lee(Corresponding Author): Funding Sunita Yadav: Manuscript Drafting.
Correspondence to Jana Petrů, Joon Sang Lee or Srinidhi Campli.
The authors declare no competing interests.
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Open Access This article is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License, which permits any non-commercial use, sharing, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if you modified the licensed material. You do not have permission under this licence to share adapted material derived from this article or parts of it. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by-nc-nd/4.0/.
Reprints and permissions
Satpute, J., Petrů, J., Hiwase, V. et al. Experimental evaluation of Al2O3–water nanofluid for efficiency enhancement in a photovoltaic–thermal system under Western Indian climate. Sci Rep 16, 3871 (2026). https://doi.org/10.1038/s41598-025-33864-0
Download citation
Received:
Accepted:
Published:
Version of record:
DOI: https://doi.org/10.1038/s41598-025-33864-0
Anyone you share the following link with will be able to read this content:
Sorry, a shareable link is not currently available for this article.
Provided by the Springer Nature SharedIt content-sharing initiative
Advertisement
Scientific Reports (Sci Rep)
ISSN 2045-2322 (online)
© 2026 Springer Nature Limited
Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.