Simulated Lead-Free Hydride Perovskite Solar Cell Exceeds 29 Percent Efficiency – Bioengineer.org

Simulated Lead-Free Hydride Perovskite Solar Cell Exceeds 29 Percent Efficiency
A comprehensive numerical modeling investigation using the SCAPS-1D platform has revealed that an environmentally benign, lead-free hydride double-perovskite absorber, designated as K2MnTlH6, holds significant promise for high-performance photovoltaic devices. Metal-halide perovskite solar cells have advanced remarkably over the past decade, achieving power conversion efficiencies exceeding 26 percent. However, most leading formulations rely on toxic lead compounds, raising substantial concerns regarding environmental contamination, operational durability, and regulatory compliance. To circumvent these challenges without sacrificing optoelectronic quality, the research team analyzed the theoretical photovoltaic capabilities of K2MnTlH6 paired with selective charge-transport layers, identifying conditions under which power conversion efficiencies surpass 29 percent under standard AM1.5G solar illumination.
Hydride double perovskites represent an emerging subclass of double-perovskite materials defined by the general formula A2BB′H6, in which hydrogen serves as the anionic species instead of traditional halogens. Prior first-principles density functional theory computations demonstrated that hydride double perovskites, specifically X2MnTlH6 where X represents sodium or potassium, possess favorable semiconducting traits, suitable bandgaps, and robust charge-transport behavior. In K2MnTlH6, combining potassium, manganese, and thallium cations enables electronic band engineering through cation ordering, d-orbital interactions, and controlled lattice distortions. Until this study, however, the practical suitability of K2MnTlH6 as an active photovoltaic absorber had remained largely unexplored.
The fundamental physical parameters of K2MnTlH6—including a narrow optical bandgap of 1.12 eV, an electron affinity of 4.00 eV, and balanced electron and hole mobilities of 20 square centimeters per volt-second—were established from published density functional theory calculations and benchmarked against structurally analogous double-perovskite systems. The simulation framework incorporated standard Poisson, carrier continuity, and drift-diffusion equations to solve for internal electrostatic potentials, charge distributions, carrier generation profiles, and recombination rates under 300 Kelvin ambient operating conditions.
A critical stage of device design involved selecting transport layers capable of establishing favorable band alignment and facilitating charge collection while suppressing interfacial carrier recombination. The investigators evaluated five distinct electron-transport materials: tungsten disulfide, indium gallium zinc oxide, buckminsterfullerene C60, PCBM, and titanium dioxide. Tungsten disulfide clearly outperformed competing candidates, achieving a baseline power conversion efficiency of 23.09 percent, a fill factor of 81.55 percent, a short-circuit current density of 31.14 milliamperes per square centimeter, and an open-circuit voltage of 0.9093 volts.
In parallel, the team benchmarked five hole-transport materials to optimize anode-side carrier extraction: CBTS, poly(3-hexylthiophene-2,5-diyl), cupric oxide, copper iron tin sulfide, and vanadium pentoxide. CBTS delivered the highest overall efficiency, matching the premier electron-transport configuration through optimal valence-band alignment and pronounced recombination suppression. As an inorganic compound synthesized from earth-abundant elements, CBTS offers distinct economic and environmental advantages over conventional organic hole-transporting matrices.
Systematic optimization of the physical dimensions, bulk defect density, and intentional doping concentration of the K2MnTlH6 absorber layer proved essential to maximizing power output. As the absorber thickness was increased from 0.2 to 1.2 micrometers, the short-circuit current density climbed from 23.66 to 32.42 milliamperes per square centimeter due to expanded light absorption, whereas the open-circuit voltage decreased slightly from 0.954 to 0.877 volts as a consequence of longer bulk carrier transit paths and elevated volume recombination. The simulation revealed an optimal intermediate thickness window between 0.8 and 1.0 micrometers. Furthermore, keeping the bulk defect density below 10 to the 13th power per cubic centimeter prevented severe recombination losses, whereas raising acceptor doping from 10 to the 13th power to 10 to the 18th power per cubic centimeter strengthened the built-in electric field, boosting the open-circuit voltage from 0.9086 to 1.0366 volts and the fill factor to 88.49 percent.
Evaluating the geometrical thickness of the transport layers revealed contrasting device sensitivities. Varying the tungsten disulfide electron-transport layer thickness between 0.1 and 0.5 micrometers had an almost negligible impact on electrical parameters, maintaining an open-circuit voltage of 0.9093 volts and an efficiency near 23.09 percent. Conversely, the solar cell exhibited marked sensitivity to the thickness of the CBTS hole-transport layer: expanding CBTS thickness from 0.1 to 0.5 micrometers caused a substantial decrease in short-circuit current density from 37.90 down to 31.14 milliamperes per square centimeter and lowered overall power conversion efficiency from 28.33 to 23.09 percent.
Interfacial defect states at both heterojunction boundaries were analyzed to delineate recombination mechanisms under non-ideal contact conditions. The tungsten disulfide/K2MnTlH6 interface exhibited stable photovoltaic performance across defect densities ranging from 10 to the 8th power to 10 to the 12th power per square centimeter, but suffered severe voltage degradation once interface defect levels exceeded 10 to the 13th power per square centimeter, driving open-circuit voltage down to 0.6696 volts and efficiency to 17.04 percent at 10 to the 18th power per square centimeter. In comparison, the K2MnTlH6/CBTS junction displayed exceptional defect tolerance, preserving baseline electrical performance up to 10 to the 13th power per square centimeter and showing only moderate degradation at extreme defect levels, underscoring the structural compatibility and charge-transfer stability of the CBTS interface.
Device robustness was further scrutinized under varying operational parasitic resistances and thermal stresses. Increasing series resistance from 2 to 10 ohm-square centimeters caused significant internal power dissipation, reducing fill factor from 65.86 to 42.58 percent and dropping power conversion efficiency from 15.48 to 10.00 percent while leaving open-circuit voltage largely unchanged. Conversely, elevating shunt resistance from 100 to 10 to the 6th power ohm-square centimeters suppressed leakage current paths, lifting fill factor from 61.90 to 81.55 percent and efficiency to 23.09 percent. Thermal simulations conducted between 280 and 420 Kelvin illustrated a steady decline in efficiency from 23.91 down to 17.23 percent, predominantly caused by thermal voltage degradation as elevated temperatures amplify intrinsic carrier concentrations and accelerate carrier recombination.
Following comprehensive multi-parameter optimization of layer thicknesses, intentional doping profiles, and interfacial contacts, the fully optimized K2MnTlH6 solar cell configuration achieved an open-circuit voltage of 1.13 volts, a short-circuit current density of 34.74 milliamperes per square centimeter, a fill factor of 83.56 percent, and an overall power conversion efficiency of 29.41 percent. In comparative benchmark evaluations against previously published lead-free perovskite models, the proposed architecture demonstrates competitive and superior theoretical performance relative to systems utilizing BaZrS3, KSnI3, and CsSnCl3.
Subject of Research: Numerical SCAPS-1D simulation of lead-free K2MnTlH6 double perovskite solar cells
Article Title: Lead-free K2MnTlH6 double perovskite solar cells with WS2/CBTS interfaces achieving > 29% efficiency: a comprehensive SCAPS-1D simulation study
Article References: Saidani, O., Yousfi, A., Abdullah, M. M. S., Al-Lohedan, H. A., Benaniba, S., Boubaaya, R., Djendel, M., Brahimi, A., & Alemu, M. T. (2026). Lead-free K2MnTlH6 double perovskite solar cells with WS2/CBTS interfaces achieving > 29% efficiency: a comprehensive SCAPS-1D simulation study. Materials for Renewable and Sustainable Energy, 15(3), Article 38. https://doi.org/10.1007/s40243-026-00382-6
Image Credits: AI Generated
DOI: 10.1007/s40243-026-00382-6
Keywords: perovskite solar cells, lead-free photovoltaics, double perovskite, hydride perovskite, K2MnTlH6, SCAPS-1D simulation, photovoltaic efficiency, WS2 electron transport layer, CBTS hole transport layer, heterojunction band alignment, recombination dynamics, interfacial defects, clean energy technology, optoelectronics, solar cell modeling, sustainable photovoltaics
News Source: Denise Maddox. (November 21, 2026). Simulated Lead-Free Hydride Perovskite Solar Cell Exceeds 29 Percent Efficiency. Scienmag.
We bring you the latest biotechnology news from best research centers and universities around the world. Check our website.
Enter your email address to subscribe to this blog and receive notifications of new posts by email.


Bioengineer.org © Copyright 2023 All Rights Reserved.
Login to your account below




Please enter your username or email address to reset your password.


Bioengineer.org © Copyright 2023 All Rights Reserved.

source

This entry was posted in Renewables. Bookmark the permalink.

Leave a Reply